Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> Firmware for the following devices has been updated to 14.32.1010:

P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)

Firmware for the following device has been updated to 16.35.3502:

P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)

New features and changes included in firmware version 14.32.1010:

Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
Limited the external loopback speed to the used module's capabilities.
Improved linkup time when using the fast linkup capability.
Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.

New features and changes included in firmware version 16.35.3502:

Modified the TCP IPv4 flows so that the steering TIR rx_hash_symmetric field is now valid only when both the SRC and DST fields are not set to zero.

]]> The following issues have been fixed in firmware version 14.32.1010:

Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
The system could not create more than 128K QPs.
On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
Packet Pacing rate was used if asymmetric VFs was enabled.
Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.

No fixes are included in firmware version 16.35.3502.

]]> Firmware for the following devices has been updated to 14.32.1010:

P21930-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4121A-XCAT Adapter)
P11341-B21 (HPE Ethernet 10Gb 2-port SFP+ MCX4621A-ACAB OCP3 Adapter)

Firmware for the following device has been updated to 16.35.3006:

P21927-B21 (HPE Ethernet 100Gb 2-Port QSFP28 MCX516A-CCHT Adapter)

New Features and changes included in version 1.0.10(A):

Version 1.0.10(A) has been recompiled to create the firmware RPM compatible with RPM LIB v4.14.2. As a result, this rebuild firmware version 1.0.10(A) can now be installed successfully on a node with FIPS enabled.

New features and changes included in version 14.32.1010:

Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
Limited the external loopback speed to the used module's capabilities.
Improved linkup time when using the fast linkup capability.
Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.

New features and changes included in version 16.35.3006:

Enabled ACS for single port cards.
Added vPort counters after creating the LAG demux table to count kernel packets reaching all the PFs participating in the LAG.

]]> The following issues have been fixed in version 14.32.1010:

Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
The system could not create more than 128K QPs.
On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
Packet Pacing rate was used if asymmetric VFs was enabled.
Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.

The following issues have been fixed in version 16.35.3006:

Packet loss that occurred when restarting the transmit.
An issue that prevented RoCE malformed packets (UDP packet with dest_port equal to RoCE well known udp_dport (0x4791)) from being counted on the vport_counter when the function disables RoCE (through MODIFY_NIC_VPORT_CONTEXT command).
A memory leakage that occurred when closing connected QPs (Type RC/UC/XRC/DC).
Added a missing VLAN strip.

]]>

Support new ML110 and DL560 Gen11 servers

]]> Support new ML110 and DL560 Gen11 servers

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Added support for Microsoft Windows Server 2025.

]]>

Added support for Microsoft Windows Server 2022.

]]>

Maintenance firmware release to introduce fixes from previous firmware.

]]>

Fixed flashing issue through SDR method

]]> TBD

]]> This product addresses an issue where BSOD is seen.

]]>

Fix for V6 Read disturb issue (which might have caused data integrity issue) and other issues.

For more information, refer to HPE Customer Bulletin at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00136659en_us

]]>

Fix for V6 Read disturb issue (which might have caused data integrity issue) and other issues.

]]> Updated to driver version 14.4.313.0

The raw driver files can be obtained by extracting the Smart Component and then extracting the Emulex installer. Use this command:

elxdrvr-fc-version.exe /q2 extract=2

The extracted files are located:

C:\Users\Administrator\Documents\Emulex\Drivers\FC-version

Each kit folder has subsequent architecture folders with subsequent OS folders. For example,

C:\Users\Administrator\Documents\Emulex\Drivers\FC-version\x64\win2019

]]> Updated to driver version 14.2.537.0

The raw driver files can be obtained by extracting the Smart Component and then extracting the Emulex installer. Use this command:

elxdrvr-fc-version.exe /q2 extract=2

The extracted files are located:

C:\Users\Administrator\Documents\Emulex\Drivers\FC-version

Each kit folder has subsequent architecture folders with subsequent OS folders. For example,

C:\Users\Administrator\Documents\Emulex\Drivers\FC-version\x64\win2019

]]> This product enhanced the compatibility with the latest drivers.

]]> This product now supports Red Hat Enterprise Linux 9 Update 3.

]]>

Added Supported Environments

Added Supported Platforms

]]>

This firmware provides bug fixes for the P5620/P5520.

]]> TBD

]]>

This product now supports Red Hat Enterprise Linux 8 update 9.

This product now supports FIPS-enabled mode.

This product now supports FW debug dump via debugfs.

This product enhances driver's robustness when bringing interface up/down with link-down-on-close flag is set and recoverable non-critical error occurs.

]]>

This product fixes a firmware issue that could result in a firmware reset when some ports have flow control enabled.

This product fixes an issue where double VLAN traffic might RSS into the first queue.

This product fixes an issue where upon creating new VLAN devices or setting the port VLAN for the VF device, and the irdma module is also loaded, a system hang might occur.

]]> Updated to version 1.0.0.1

]]> This product now supports Red Hat Enterprise Linux 9 update 4.

]]>

This product fixes an issue where VLAN set operation may leads to deadlock.

This product fixes an issue where a NULL pointer dereference in early reset.

This prodcut fixes an issue where users fail to change the number of queues (channels).

This product fixes an issue where system hang when VFs are created and VLAN configured.

]]> This product now supports Red Hat Enterprise Linux 9 update 4.

]]>

This product fixes an issue where VLAN set operation may leads to deadlock.

This product fixes an issue where a NULL pointer dereference in early reset.

This prodcut fixes an issue where users fail to change the number of queues (channels).

This product fixes an issue where system hang when VFs are created and VLAN configured.

]]> This Firmware package contains following firmware versions:

Adapter	Speed	Universal Boot Image	Firmware	UEFI	Boot Bios
HPE SN1200E 16Gb Dual Port Fibre Channel Host Bus Adapter	16Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1200E 16Gb Single Port Fibre Channel Host Bus Adapter	16Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1600E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1600E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter	64Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0
HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter	64Gb	14.4.329.10	14.4.329.10	14.4.329.9	14.4.290.0

]]>

Fix for V6 Read disturb issue (which might have caused data integrity issue) and other issues.

For more information, refer to HPE Customer Bulletin at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00136659en_us

]]>

Fix for V6 Read disturb issue (which might have caused data integrity issue) and other issues.

]]> TBD

]]> This product enhanced the compatibility with firmware of Fortville 9.4.

]]> This product corrects an issue where the adapter may go offline after firmware is flashed, but before reboot.

]]> Updated to version 1.0.0.1

]]> Important : Security Hardening Enhancements - This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device firmware to this version to improve the firmware security and reliability of your device.

New features and changes included in version 16.35.4030:

Added support for postponing QP timeout "retry exceeded" errors for traffic directed at specific destinations. This new capability prevents broken connections for destinations in downtime because of live migration.

]]> The following issues have been fixed in version 16.35.4030:

VF FLR would get stuck when its PF triggered the FLR as well.
Unexpected source UDP port appeared in RoCE packets when the firmware ignored a non-PF driver configuration for RoCE source UDP port control (as set in SET_HCA_CAP.sw_r_roce_src_udp_port).

New features and changes included in version 16.35.3502:

Modified the TCP IPv4 flows so that the steering TIR rx_hash_symmetric field is now valid only when both the SRC and DST fields are not set to zero.

]]> No fixes are included in version 16.35.3502.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> This product introduced power restrictions of 4.5 watts per port.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

This product addressed an issue where data is interchanged of Port 1 and Port 4 when running a Redfish GET Operation under the NetworkAdapter, NetworkDeviceFunctions and Port Schema with "Metrics" properties.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

]]>

Improve the FW about data mismatch after SPL issued.

]]>

Improve the FW about data mismatch after SPL issued.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]> Updated to version 9.4.10.20

]]> Updated to version 9.4.9.21

]]>

Added support for Microsoft Server Windows 2025.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel Product Update (IPU) version IPU.2024.3 guidance. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.002.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving the configuration page of an MR controller.

Addressed an issue where Windows Server 2025 HLK TPM2.0 UEFI Preboot Interface test failed on XL450Gen10.

Addressed an issue where the "Physical Drive missing" message appeared twice in POST when a drive was removed and rebooted with incorrect severity in IML.

Addressed an issue where the boot order was cleared unexpectedly after configuring System Configuration (RBSU) options and navigating to Boot Options > UEFI Boot Settings > UEFI Boot Order, and then pressing F12 to Save and Exit.

Known Issues:

None]]> Added value "C6 without C1E" in System Configuration (RBSU) option "Power Management/Advanced Power Options menu/Minimum Processor Idle Power Core C-State". When selected, the Minimum Processor Idle Power Core C-State is C6 with C1E disabled. This setting has the following Redfish property: /redfish/v1/systems/1/bios/MinProcIdlePower

]]> Important Notes:

This revision of the System ROM includes the mitigation for security vulnerabilities CVE-2021-38578, CVE-2023-5678 and CVE-2024-0727. The security vulnerabilities are documented in the CVE report site. They are not unique to HPE servers. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.01.05.002.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where system may encounter a RSOD while updating SAS drive FW via HPE Service Packs, including, but not limited to, VMware ESXi Online HDD FW Component Bundle 16.00, HPE Synergy Service Pack (SSP) 2024.01.02 (January 2024) and the future HPE Synergy Service Pack (SSP) 2024.07.01 (July 2024).

Known Issues:

None]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel Product Update (IPU) version IPU.2024.3 guidance.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving configuration page of an MR controller.

Addressed an issue that Battery Failure IML message log may be incorrectly logged for MR Controller with Smart Storage Battery.

Addressed an issue where system failed to boot with selected NVMe HDD by setting One-Time Boot Option in ILO Web.

Known Issues:

None]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.00.03.604 (2.00_12_20_2023). This version of the System ROM contains updates aligned with the Intel Product Update (IPU) version IPU.2024.1 guidance. This revision of the System ROM includes the mitigation for security vulnerabilities CVE-2023-45229, CVE-2023-5678, and CVE-2021-38578. The security vulnerabilities are documented in the CVE report site. They are not unique to HPE servers. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 06.00.03.604 (2.00_12_20_2023).

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the boot order was cleared unexpectedly after configuring System Configuration (RBSU) options, navigating to Boot Options > UEFI Boot Settings > UEFI Boot Order, and then pressing F12 to Save and Exit.

Removed the value of "Not Specified" in System Configuration (RBSU) option "Server Security/Trusted Platform Module Options/Current TPM 2.0 Active PCRs" and set the default value as "SHA1 and SHA256".

Known Issues:

None]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]> This product introduced power restrictions of 4.5 watts per port.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Added support for Microsoft Server Windows 2025.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]> Added support for Microsoft Server Windows 2025.

]]>

This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.

The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.

Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.

]]>

This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.

The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.

Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.

]]>

This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.

The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.

Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.

]]>

This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.

The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.

Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]> Features included in version 28.41.1000:

Added the TX_SCHEDULER_FWS_REACTIVITY nvconfig flag to solved an mlnx_qos ETS settings issue.
Improved ZTR_RTTCC algorithm fairness when running with 4K MTU.
Changed BER monitor default values to alarm on symbol and effective BER.
Added support for the following prefetch fields on ODP event:

pre_demand_fault_pages, post_demand_fault_pages.

Implemented Deterministic Random Bit Generator (DRBG) algorithm on top of firmware TRNG (the source for raw data input) in accordance with NIST SP800-90A.
Added support for 400GbE speed (8X50G) in Single-Port OSFP adapter cards including link training and auto-negotiation when connecting OSFP to OSPF-RHS cables.
Added support for PSP in Hardware Steering.
Added a new NVConfig option to copy AR bit from the BTH header to the DHCP header.
Added the option to provide field's offset and length in Steering add_action option.
Added support for steering match on packet l4_type through FTG/FTE.
Added support for setting, adding or copying the flow_label fields from the packet.
Added support for 64KB pages.

Note: Configuring BAR_PAGE_ALIGNMENT to ALIGN_64KB(2) while one of the following is configured will cause the device to ignore the BAR_PAGE_ALIGNMENT configuration:

PF_NUM_PF_MSIX>256 on any of the Physical Functions
VIRTIO_EMULATION_HOTPLUG_TRANS/

VIRTIO_NET_EMULATION_PF_PCI_LAYOUT/
VIRTIO_NET_EMULATION_VF_PCI_LAYOUT/
VIRTIO_BLK_EMULATION_PF_PCI_LAYOUT/
VIRTIO_BLK_EMULATION_PF_PCI_LAYOUT=VIRTIO_TRANSITIONAL(1)

Extended Flex Parser merge mechanism to support hardware capabilities.
Enabled the option to disable the native parser when the parse graph node is configured with the same conditions.
Added support for father/son headers parsing.
Added support for tunnel_offload in LRO.

]]> The following issues have been fixed in version 28.41.1000:

Initial release

]]> Features included in version 28.41.1000:

Added the TX_SCHEDULER_FWS_REACTIVITY nvconfig flag to solved an mlnx_qos ETS settings issue.
Improved ZTR_RTTCC algorithm fairness when running with 4K MTU.
Changed BER monitor default values to alarm on symbol and effective BER.
Added support for the following prefetch fields on ODP event:

pre_demand_fault_pages, post_demand_fault_pages.

Implemented Deterministic Random Bit Generator (DRBG) algorithm on top of firmware TRNG (the source for raw data input) in accordance with NIST SP800-90A.
Added support for 400GbE speed (8X50G) in Single-Port OSFP adapter cards including link training and auto-negotiation when connecting OSFP to OSPF-RHS cables.
Added support for PSP in Hardware Steering.
Added a new NVConfig option to copy AR bit from the BTH header to the DHCP header.
Added the option to provide field's offset and length in Steering add_action option.
Added support for steering match on packet l4_type through FTG/FTE.
Added support for setting, adding or copying the flow_label fields from the packet.
Added support for 64KB pages.

Note: Configuring BAR_PAGE_ALIGNMENT to ALIGN_64KB(2) while one of the following is configured will cause the device to ignore the BAR_PAGE_ALIGNMENT configuration:

PF_NUM_PF_MSIX>256 on any of the Physical Functions
VIRTIO_EMULATION_HOTPLUG_TRANS/

VIRTIO_NET_EMULATION_PF_PCI_LAYOUT/
VIRTIO_NET_EMULATION_VF_PCI_LAYOUT/
VIRTIO_BLK_EMULATION_PF_PCI_LAYOUT/
VIRTIO_BLK_EMULATION_PF_PCI_LAYOUT=VIRTIO_TRANSITIONAL(1)

Extended Flex Parser merge mechanism to support hardware capabilities.
Enabled the option to disable the native parser when the parse graph node is configured with the same conditions.
Added support for father/son headers parsing.
Added support for tunnel_offload in LRO.

]]> The following issues have been fixed in version 28.41.1000:

Initial release

]]>

Improves data integrity.

The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions.

Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide a minor performance improvement.

]]>

Improves data integrity.

The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions.

Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide a minor performance improvement.

]]> Added support for Microsoft Server Windows 2025.

]]>

Provides proactive protection against contamination built up on the media and air-bearing surface of the heads by increased routine “sweeping” of the media surface.

]]>

Provides proactive protection against contamination built up on the media and air-bearing surface of the heads by increased routine “sweeping” of the media surface.

]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU.2024.1 guidance. This version of the SPS should be paired with System ROM 2.00 (02/01/2024) or later.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2024.1 guidance.

Known Issues:

None]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU.2023.3 guidance.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2023.3 guidance.

Known Issues:

None

]]> TBD

]]> This product fixed an issue that caused the collecting minidump process to crash while the device was initializing.

]]> TBD

]]>

This product now supports Red Hat Enterprise Linux 8 update 9.

This product now supports FIPS-enabled mode.

]]> This product fixes an issue where the NIC temperature status doesn't show up on iLO webpage.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Maintenance firmware release to introduce fixes from previous firmware.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]> The following new features and changes have been included in version 24.04-0.6.6.1:

Added support for Live Migration. Live migration refers to the process of moving a guest virtual machine (VM) running on one physical host to another host without disrupting normal operations or causing any downtime or other adverse effects for the end user.
Added support for multicast control path packet snooping (IGMP/MLD) and offload of MDB notifications in order to replicate multicast traffic to multiple destinations in the hardware.
Increased the netdev maximum channels from 128 to 256 for systems with a high number of cores.
Enhanced performance by removing the internal Rx path from the internal page cache, thus allowing the driver to always use the kernel's page_pool.
Enhanced performance by adding the following modifications in XDP:
- Added XDP multi-buffer support to the default RQ type (Striding RQ)
- Added support for XDP multi-buffer redirect-in
- Allowed non-linear single-segment frames in XDP TX MPWQE
Increased the maximum outstanding DC atomic reads to 32 to enable the driver to handle reads larger than 8K. Now log_max_ra_{res/req}_dc is exposed in DV API, enabling the user to see both RC and DC values.
Added support for Linux kernel DPLL subsystem as a mechanism for working with clock signals in NVIDIA's proprietary synchronous ethernet protocol daemon. This new mechanism enables the use of both VFs and SFs, and is supported starting from korg6.8.
Limited the number of MADs received on the wire that are queued in the kernel as they are waiting for the user-space application to 200k per umad file. By that, preventing malicious or faulty behavior of flooding a node with MADs and exhausting its memory.
Added the option to expose offloaded FDB state (flags, counters, etc.) via debugfs for debugging purposes.

$ cat mlx5/0000\:08\:00.0/esw/bridge/bridge1/fdb

DEV MAC VLAN PACKETS BYTES LASTUSE FLAGS

enp8s0f0_1 e4:0a:05:08:00:06 2 2 204 4295567112 0x0

enp8s0f0_0 e4:0a:05:08:00:03 2 3 278 4295567112 0x0

Added support for over KORG 6.7 read frequency_diff.

]]> The following issues have been fixed in version 24.04-0.6.6.1:

An issue related to the comparison process between the SW steering and FW steering modes to avoid kernel crashes incidences.
The tc_wrap tool did not work properly when VLAN was configured as the tool incorrectly handled the library function return value.
An IPSec issue that resulted in Crypto offload getting disabled.
Memory corruption issue when running XDP traffic.
IFA packets were sent from the incorrect port on VF LAG.
An issue that caused a deadlock in the flow of disabling the LAG when changing eswitch mode from switchdev to legacy when a LAG bond existed on the machine.
In systems with 64k page size, applications opening a substantial amount of RDMA resources such as UARs, QPs, and CQs might encounter errors during the creation of these resources due to limitations in PCI BAR size.
PFC configuration was reset when updating the cable length via mlnx_qos.

]]> No changes or new features included in version 23.10-1.1.9.1.

]]> The following issues have been fixed in version 23.10-1.1.9.1:

An error was triggered in case devlink reload was attempted when there were allocated subfunctions.
Changing the steering mode to firmware steering was unsupported for policy IPsec rules.

]]> This product fixed BSOD event not being detected when collecting mstdump on BUGCHECK while the device was already down.

]]> This product fixed an issue that caused the collecting minidump process to crash while the device was initializing.

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving the configuration page of an MR controller.

Addressed an issue where Windows Server 2025 HLK TPM2.0 UEFI Preboot Interface test failed on XL450Gen10.

Addressed an issue where the "Physical Drive missing" message appeared twice in POST when a drive was removed and rebooted with incorrect severity in IML.

Known Issues:

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Firmware maintenance release of Samsung U.3 NVMe SSD with HPK4.

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel Product Update (IPU) version IPU.2024.3 guidance.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving configuration page of an MR controller.

Addressed an issue that Battery Failure IML message log may be incorrectly logged for MR Controller with Smart Storage Battery.

Addressed an issue where system failed to boot with selected NVMe HDD by setting One-Time Boot Option in ILO Web.

Known Issues:

None]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> Added support for:

Red Hat Enterprise Linux 8.10

Red Hat Enterprise Linux 9.4

SuSE Linux Enterprise Server 15.6

Updated to version 14.4.329.9

]]> Added support for:

Red Hat Enterprise Linux 8.10

Red Hat Enterprise Linux 9.4

SUSE Linux Enterprise Server 15sp6

Updated to version 14.2.589.33

]]> TBD

]]> This product enhanced the compatibility with firmware of Fortville 9.4.

]]> This product corrects an issue where the adapter may go offline after firmware is flashed, but before reboot.

]]> This product introduced power restrictions of 4.5 watts per port.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

]]> Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

New features and changes included in version 20.41.1000:

Added support for steering match on packet l4_type through FTG/FTE.

]]> No fixes are included in version 20.41.1000.

New features and changes included in version 20.41.1000:

Added support for steering match on packet l4_type through FTG/FTE.

]]> No fixes are included in version 20.41.1000.

]]> Agentless Management Service

Fixed OID name hrSystemUptime is reported incorrectly

]]> Agentless Management Service

Extend network adapter speed support with 20,40, and 100G for CPQNIC MIB cpqNicIfPhysAdapterConfSpeedDuplex OID.

]]> Agentless Management Service

Fixed incorrect NVMe drive information displayed after hot plugging.
Fixed SSD wear status sudden peak value triggering SNMP trap false alarm.
Fixed incomplete uninstallation for amscli while upgrading Agentless Management Service.

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]> This Firmware package contains following firmware versions:

Adapter	Speed	MBI	Firmware	UEFI	Boot Bios
HPE SN1100Q 16GB Dual Port PCIe Fibre Channel Host Bus Adapter	16Gb	02.04.01	9.15.00	7.25	3.68
HPE SN1100Q 16GB Single Port PCIe Fibre Channel Host Bus Adapter	16Gb	02.04.01	9.15.00	7.25	3.68
HPE SN1600Q 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	02.04.01	9.15.00	7.25	3.68
HPE SN1600Q 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	02.04.01	9.15.00	7.25	3.68
HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	02.10.00	09.15.00	7.36	0.0
HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	02.10.00	09.15.00	7.36	0.0
HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter	64Gb	02.10.00	09.15.00	7.36	0.0
HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter	64Gb	02.10.00	09.15.00	7.36	0.0

]]> Fixed the following behavior:

Temperature Misreading: the adapter was reading incorrect reading of the temperature on the HPE SN1610Q 32Gb Fibre Channel Host Bus adapter's Small Form-factor Pluggable. The symptom would result in a temperature spike and potentially reset the system

]]> This Firmware package contains following firmware versions:

Adapter	Speed	MBI	Firmware	UEFI	Boot Bios
HPE SN1100Q 16GB Dual Port PCIe Fibre Channel Host Bus Adapter	16Gb	02.02.05	9.14.00	7.25	3.68
HPE SN1100Q 16GB Single Port PCIe Fibre Channel Host Bus Adapter	16Gb	02.02.05	9.14.00	7.25	3.68
HPE SN1600Q 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	02.02.05	9.14.00	7.25	3.68
HPE SN1600Q 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	02.02.05	9.14.00	7.25	3.68
HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	02.09.07	09.14.01	7.36	0.0
HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	02.09.07	09.14.01	7.36	0.0
HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter	64Gb	02.09.07	09.14.01	7.36	0.0
HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter	64Gb	02.09.07	09.14.01	7.36	0.0

]]> Fixed the following behavior:

]]>

This fix is for unrecovered errors may occur on the targeted Blocks of Wear-leveling process when host issues Read command.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> Important Notes:

This revision of the System ROM includes AMD reference code RomePI 1.0.0.J for AMD 2nd Generation EPYC processors. This revision of the System ROM includes AMD reference code NaplesPI 1.0.0.M for AMD 1st Generation EPYC processors.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving configuration page of MR controller.

Addressed an issue where duplicated "Physical Drive missing" may appear in POST and IML.

Known Issues:

None]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the operating system could not detect iSCSI drive through IPv6 installation when iSCSI IpAddressType was set to auto.

Known Issues:

None]]> TBD

]]> This product fixes an issue where kernel panic with call trace in qedf_ctx_soft.

]]>

Added Windows 2025 Support

]]>

Update build environment with SHA384

]]> Firmware for the following devices has been updated to 12.28.2006:

825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)

Firmware for the following devices has been updated to 16.35.3006:

879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)
872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)

Important : Security Hardening Enhancements - This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device firmware to this version to improve the firmware security and reliability of your device.

New Features and changes included in version 12.28.2006:

Increased the maximum XRQ number to 512.

New features and changes included in version 16.35.4030:

Added support for postponing QP timeout "retry exceeded" errors for traffic directed at specific destinations. This new capability prevents broken connections for destinations in downtime because of live migration.

]]> The following issues have been fixed in firmware version 12.28.2006:

Fixes an issue that caused the DCR to be destroyed before the retry option managed to work when the retry timeout is too big. In this case the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
Increased PHY power consumption limit to 1.5w.
Fixed an issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.

The following issues have been fixed in version 16.35.4030:

VF FLR would get stuck when its PF triggered the FLR as well.
Unexpected source UDP port appeared in RoCE packets when the firmware ignored a non-PF driver configuration for RoCE source UDP port control (as set in SET_HCA_CAP.sw_r_roce_src_udp_port).

]]> Firmware for the following devices has been updated to 12.28.2006:

825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)

Firmware for the following devices has been updated to 16.35.3006:

879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)
872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)

New Features and changes included in version 12.28.2006:

Increased the maximum XRQ number to 512.

New features and changes included in version 16.35.3006:

Enabled ACS for single port cards.
Added vPort counters after creating the LAG demux table to count kernel packets reaching all the PFs participating in the LAG.

]]> The following issues have been fixed in version 12.28.2006:

Fixes an issue that caused the DCR to be destroyed before the retry option managed to work when the retry timeout is too big. In this case the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
Increased PHY power consumption limit to 1.5w.
Fixed an issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.

The following issues have been fixed in version 16.35.3006:

Packet loss that occurred when restarting the transmit.
An issue that prevented RoCE malformed packets (UDP packet with dest_port equal to RoCE well known udp_dport (0x4791)) from being counted on the vport_counter when the function disables RoCE (through MODIFY_NIC_VPORT_CONTEXT command).
A memory leakage that occurred when closing connected QPs (Type RC/UC/XRC/DC).
Added a missing VLAN strip.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Added support for Microsoft Windows Server 2022.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]> See the iSUT Release Notes for information about the issues resolved in this release

]]>

Update maximum continuous operation temperature values for host thermal management and reporting.

]]>

Update maximum continuous operation temperature values for host thermal management and reporting.

]]> This Firmware package contains following firmware versions:

Adapter	Speed	MBI	Firmware	UEFI	Boot Bios
HPE SN1100Q 16GB Dual Port PCIe Fibre Channel Host Bus Adapter	16Gb	02.04.01	9.15.00	7.25	3.68
HPE SN1100Q 16GB Single Port PCIe Fibre Channel Host Bus Adapter	16Gb	02.04.01	9.15.00	7.25	3.68
HPE SN1600Q 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	02.04.01	9.15.00	7.25	3.68
HPE SN1600Q 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	02.04.01	9.15.00	7.25	3.68
HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	02.10.00	09.15.00	7.36	0.0
HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	02.10.00	09.15.00	7.36	0.0
HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter	64Gb	02.10.00	09.15.00	7.36	0.0
HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter	64Gb	02.10.00	09.15.00	7.36	0.0

]]> This Firmware package contains following firmware versions:

Adapter	Speed	MBI	Firmware	UEFI	Boot Bios
HPE SN1100Q 16GB Dual Port PCIe Fibre Channel Host Bus Adapter	16Gb	02.02.05	9.14.00	7.25	3.68
HPE SN1100Q 16GB Single Port PCIe Fibre Channel Host Bus Adapter	16Gb	02.02.05	9.14.00	7.25	3.68
HPE SN1600Q 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	02.02.05	9.14.00	7.25	3.68
HPE SN1600Q 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	02.02.05	9.14.00	7.25	3.68
HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter	32Gb	02.09.07	09.14.01	7.36	0.0
HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter	32Gb	02.09.07	09.14.01	7.36	0.0
HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter	64Gb	02.09.07	09.14.01	7.36	0.0
HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter	64Gb	02.09.07	09.14.01	7.36	0.0

]]> Important Notes:

Ver. 1.0.0.22(B) contains updates to the firmware packaging and is functionally equivalent to ver. 1.0.0.22. It is not necessary to upgrade with Revision B if a previous component revision was used to upgrade the firmware to version 1.0.0.22.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where Innovation Engine (IE) may improperly reset every 24 hours.

Known Issues:

None

]]> Important Notes:

None

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where Innovation Engine (IE) may improperly reset every 24 hours.

Known Issues:

None

]]>

]]> The following issues have been fixed in driver version 4.22.73.1006:

Performance issues were observed due to context switches over the hardware priority buffers that caused slower packet being sent when sending traffic with many different VLAN (CoS PCP/801.2p) priorities. To fix the issue, the driver provides a new module parameter trust_dscp_same_priority to map all DSCP priorities to the same traffic class to avoid such behavior.
A specific steering rule creation issue when the teaming mode is on.
Packets were dropped by ENS that were not set as MARK. Now MARK actions are available in both LAG and no LAG modes.

]]> New features and changes in driver version 4.22.73.1004:

Firmware CR dump will now be collected automatically into ZDUMP PSOD or on livedump for debuggability purposes.
Enabled the driver to read the temperature from private statistics.

To see the temperature, run:# nsxdp-cli ens uplink stats get -n vmnic1 | grep -i asicSensorTemperature

Added support for Hardware Accelerated GENEVE and VXLAN encapsulation and decapsulation for RoCE traffic.
Hardware accelerated flows can now be mirrored using the standard packet capture tools.
Added the ability to offload NSX Distributed Firewall rules by using in-hardware tracking of packet flows.
RSS support for ENS Model 1 improves performance using fewer CPU cores. This capability can be enabled using the "netq_rss_ens" module parameter.

]]> Fixes included in driver version 4.22.73.1004:

Fixed an issue that caused a ParaVirtual VM to lose traffic after resuming from the suspend mode when SR-IOV was enabled in the system.
Cleaned steering rule from FDB when VF is being quiesced.
Fixed an issue that caused the driver to configure the incorrect SL value for RoCE with RDMACM.

]]>

Added support for Microsoft Server Windows 2025.

]]>

Mitigates the potential drive FW halt issue.

]]> Important Notes:

Ver. 06.00.03.604(B) contains updates to the firmware packaging and is functionally equivalent to ver. 06.00.03.604. It is not necessary to upgrade with Revision B if a previous component revision was used to upgrade the firmware to version 06.00.03.604.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2024.1 guidance.

Known Issues:

None

]]> Important Notes:

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2024.1 guidance.

Known Issues:

None]]> See the AMS Release Notes for information about the enhancements in this release.

]]> See the AMS Release Notes for information about the issues resolved in this release.

]]>

Removed files based on CVE-2020-14152, CVE-213-6629.

Removed workload log page check to prevent SSD device lifetime.

]]>

Fixed AMS crashed issue caused by non-ASCII code set environment.

Fixed internal packaging related issues.

]]> Updated to version 3.3-3

This Component is FIPs enabled.

]]> This Component is FIPs enabled.

]]> Updated to version 3.3-3

]]>

Added support for Microsoft Windows Sever 2025.

]]>

Added support for Microsoft Windows Sever 2022.

]]> This product introduced power restrictions of 4.5 watts per port.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

]]>

Improves performance in certain file systems and implements fixes for several of the previous firmware’s shortcomings.

The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions.

Several maintenance items are included in this firmware revision that reduce the probability of hangs.

]]>

Improves performance in certain file systems and implements fixes for several of the previous firmware’s shortcomings.

The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions.

Several maintenance items are included in this firmware revision that reduce the probability of hangs.

]]>

Update build environment with SHA384

Update OS

]]> Initial Release

]]> The following fixes were incorporated in this version:

The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.
The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.
Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.
If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> The following fixes were incorporated in this version:

The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.
The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.
Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.
If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]>

Added support for Microsoft Server Windows 2025.

]]>

Added support for Microsoft Server Windows 2022.

]]> TBD

]]> This product correct an issue which the component can't read the current driver version.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> Important Notes:

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2024.1 guidance.

Known Issues:

None

]]> Important Notes:

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2024.1 guidance.

Known Issues:

None]]>

Added support for Microsoft Windows Server 2025.

]]>

Added support for Microsoft Windows Server 2022.

]]> Added support for Microsoft Server Windows 2025.

]]>

Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.

]]>

Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.

]]>

Maintenance firmware release to introduce fixes from previous firmware.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]> Important Notes:

None

Firmware Dependencies:

For HPE ProLiant Gen10 Plus servers, iLO5 version 2.55 or above is required to upgrade to this version.

Enhancements/New Features:

Changed certain behaviors to avoid machine power failures when significant power consumption devices are introduced.

Problems Fixed:

None

Known Issues:

None

]]> Important Notes:

None

Firmware Dependencies:

For HPE ProLiant Gen10 Plus servers, iLO5 version 2.55 or above is required to upgrade to this version.

Enhancements/New Features:

Changed certain behaviors to avoid machine power failures when significant power consumption devices are introduced.

Problems Fixed:

None

Known Issues:

None

]]>

This is a maintenance release that contains code improvements for CAP.TO and LED behavior.

]]> This is an initial FW.

]]> Added support of ESXi 8.0 U1

]]> The following fixes were incorporated in this version:

The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.
The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.
Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.
If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> The following fixes were incorporated in this version:

The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.
The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.
Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.
If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> This product introduced power restrictions of 4.5 watts per port.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

]]>

Firmware contains fix for bug that may cause drive to perform self-initiated reset in systems where maximum queue depth of 128 is exceeded.

]]>

Firmware contains fix for bug that may cause drive to perform self-initiated reset in systems where maximum queue depth of 128 is exceeded.

]]>

Updated Supported Environments

]]>

Updated SBOM requirement

]]>

Mitigates the potential drive FW halt issue.

]]>

Mitigates the potential drive FW halt issue.

]]>

Update maximum continuous operation temperature values for host thermal management and reporting.

Assert fixes, logging enhancements and all current firmware improvements.

]]>

Update maximum continuous operation temperature values for host thermal management and reporting.

Assert fixes, logging enhancements and all current firmware improvements.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> Firmware for the following device has been updated to 14.32.1010:

P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)

New features and changes included in version 14.32.1010:

Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
Limited the external loopback speed to the used module's capabilities.
Improved linkup time when using the fast linkup capability.
Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.

]]> The following issues have been fixed in sub-version 1.0.6(C):

Transaction test error was reported while deploying the component using SPP from HPE Linux SDR.

The following changes have been made in sub-version 1.0.6(B):

Product rebuilt to support FIPS mode enabled OS environment.

The following changes have been made in sub-version 1.0.6(A):

Product rebuilt to have the new SHA 384 signature.

The following issues have been fixed in version 14.32.1010:

Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
The system could not create more than 128K QPs.
On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
Packet Pacing rate was used if asymmetric VFs was enabled.
Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.

]]> Firmware for the following device has been updated to 14.32.1010:

P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)

New features and changes included in version 14.32.1010:

Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
Limited the external loopback speed to the used module's capabilities.
Improved linkup time when using the fast linkup capability.
Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.

]]> The following changes have been made in sub-version 1.0.6(B):

Product rebuilt to support FIPS mode enabled OS environment.

The following changes have been made in sub-version 1.0.6(A):

Product rebuilt to have the new SHA 384 signature.

The following issues have been fixed in version 14.32.1010:

Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
The system could not create more than 128K QPs.
On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
Packet Pacing rate was used if asymmetric VFs was enabled.
Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> Added the System Configuration (RBSU) option "Processor Options/AMD IC Config Disable IT Bypass" and set to "Disabled" by default. Enable this option if a UMCE with Bank 0x03 and Synd[0]=1 logged in IML on EPYC 7003 processors.

This setting has the following Redfish property:

/redfish/v1/systems/1/bios/settings/AmdIcConfigDisableITBypass

]]> Important Notes:

This revision of the System ROM includes AMD reference code MilanPI 1.0.0.D for AMD 3rd Generation EPYC processors. This revision of the System ROM includes AMD reference code RomePI 1.0.0.J for AMD 2nd Generation EPYC processors.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving configuration page of MR controller.

Addressed an issue where Redfish BIOS actions, ResetBIOS and ChangePassword may not work.

Addressed an issue that Battery Failure IML message log may be incorrectly logged for MR Controller with Smart Storage Battery.

Addressed an issue where system failed to boot with selected NVMe HDD by setting One-Time Boot Option in ILO Web.

Known Issues:

None]]> Important Notes:

This revision of the System ROM includes the mitigation for security vulnerabilities CVE-2023-31315 for AMD 2nd and 3rd Generation EPYC processors. This revision of the System ROM includes the mitigation for security vulnerabilities CVE-2023-45853, CVE-2023-45229, CVE-2022-36763, CVE-2022-36764, CVE-2023-5678, CVE-2021-38575 and CVE-2021-38578. The security vulnerabilities are documented in the CVE report site. They are not unique to HPE servers. This revision of the System ROM includes AMD reference code MilanPI 1.0.0.D for AMD 3rd Generation EPYC processors. This revision of the System ROM includes AMD reference code RomePI 1.0.0.H for AMD 2nd Generation EPYC processors.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the operating system could not detect iSCSI drive through IPv6 installation when iSCSI IpAddressType was set to auto.

Addressed an issue where system would not complete POST after BIOS firmware updated to ver 3.00 with E810-XXVDA4''s installed.

Addressed an issue where system would hang with ASSERT during POST after adding DIMMs.

Known Issues:

None]]> The following fixes were incorporated in this version:

Smart Array reporting "Storage Enclosure FW upgrade Problem Detected".
PSU version is showing as "No Ver" after inserted the New bel power PSU.
GEM_5_2 Coverity defect fix.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> The following fixes were incorporated in this version:

Smart Array reporting "Storage Enclosure FW upgrade Problem Detected".
PSU version is showing as "No Ver" after inserted the New bel power PSU.
GEM_5_2 Coverity defect fix.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]>

Fix for Uncorrectable Machine Check Exception (UMCE) issue which might occur.

]]>

Fixed CA https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00126514en_us

]]>

Improve random read/write perfomance.

]]> Added support for:

Red Hat Enterprise Linux 8.10

Red Hat Enterprise Linux 9.4

SuSE Linux Enterprise Server 15.6

Updated to version 14.4.329.9

]]> Added support for:

Red Hat Enterprise Linux 8.10

Red Hat Enterprise Linux 9.4

SUSE Linux Enterprise Server 15sp6

Updated to version 14.2.589.33

]]>

Added support for Microsoft Server Windows 2025.

]]>

Added support for Microsoft Server Windows 2022.

]]>

Add support for Windows Server 2025

]]> This product is updated to maintain compatibility with CS5.0 compliance

]]> This product is updated to maintain compatibility with CNSA (Commercial National Security Algorithm) compliance.

]]>

This product correct an issue where System crash while upgrading with NPAR SRIOV-EP mode enabled.

This product correct an issue where BSOD in Windows NDIS driver while in WS2022 PCS Configuration.

]]> TBD

]]>

This product fixed error checking sequence for Firmware Management Protocol API.

This product fixed NC-SI commands to interoperate more benefit with iLO.

]]>

This maintenance revision improves data integrity. The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions.

For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00138902en_us which will be active on 24-April-2024.

]]>

This maintenance revision improves data integrity. The risk of not upgrading to this firmware is the increased possibility of data corruption in certain error and timing conditions.

For more information, refer to HPE Customer Advisory at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00138902en_us which will be active on 24-April-2024.

]]>

Update build environment with SHA384

Update OS

]]>

Modify Product ID to "A4200 Gen10P LFF" and "A4200 Gen10P SFF" to distinguish the different generation expander backplane.

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving configuration page of MR controller.

Addressed an issue where Redfish BIOS actions, ResetBIOS and ChangePassword may not work.

Addressed an issue that Battery Failure IML message log may be incorrectly logged for MR Controller with Smart Storage Battery.

Known Issues:

None]]> Added the System Configuration (RBSU) options "PCIe Device Configuration/Advanced PCIe Configuration/PCIe Data Link Feature/PCIe Slot XX Data Link Feature Exchange" and set to "Enabled" by default. These options can be used to disable Data Link Feature Exchange when a legacy (Gen 3 or older) PCIe card is installed, which is not compatible with this feature. This setting has the following Redfish properties:

/redfish/v1/systems/1/bios/settings/SlotXXDataLinkFeatureExchange

]]> Important Notes:

This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 04.04.04.603 (2.00_12_18_2023).

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the RBSU/Firmware update shows "Flash successfully" message when incorrect SATA firmware was loaded for upgrade.

Addressed an issue where system failed to boot with selected NVMe HDD by setting One-Time Boot Option in ILO Web.

Known Issues:

None]]>

Added support for Microsoft Windows Server 2025.

]]>

Added support for Microsoft Windows Server 2022.

]]> The following enhancement has been added in this version:

Added support of RHEL 8.7
Added support ofRHEL 9.1
Added support of SLES15 SP4

]]> The following fixes were incorporated in this version:

Temperature sensors logic inside gSEP model and SES database
When an IOM is pulled the surviving IOM reports false critical temperatures

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> The following enhancement has been added in this version:

Added support of Rhel 7.8
Added support of Rhel 8.2
Added support of SLES15 SP2

]]> The following fixes were incorporated in this version:

Temperature sensors logic inside gSEP model and SES database
When an IOM is pulled the surviving IOM reports false critical temperatures

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Added support for Microsoft Server Windows 2025.

]]>

Added support for Microsoft Server Windows 2022.

]]>

Updated supported environments

Updated supported platforms

]]>

This product enhances the Get Package Status command support.

This product enhances to add a warning message when a non-supported dual-rate transceiver is used.

This product enhances the Addition of SFF 8472 Transceiver Power Details to RDE Port Metrics.

]]>

This product addresses an issue where getting Transceiver Temperature erroneous unit value.

This product addresses an issue when NC-SI Query Pending NC PLDM Response is wrong when NIC does not have a pending PLDM request.

]]>

This product enhances the Get Package Status command support.

This product enhances to add a warning message when a non-supported dual-rate transceiver is used.

This product enhances the Addition of SFF 8472 Transceiver Power Details to RDE Port Metrics.

]]>

This product addresses an issue where getting Transceiver Temperature erroneous unit value.

This product addresses an issue when NC-SI Query Pending NC PLDM Response is wrong when NIC does not have a pending PLDM request.

]]>

Added support for Microsoft Server Windows 2025.

]]>

Added support for Microsoft Server Windows 2022.

]]> MFT prerequisite RPMs for Mellanox adapter firmware update in Secure Boot mode.

]]> Firmware for the following device has been updated to 14.32.1010:

P11338-B21 (HPE Ethernet 10Gb 2-port 548SFP+ Adapter)

New features and changes included in version 14.32.1010:

Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
Limited the external loopback speed to the used module's capabilities.
Improved linkup time when using the fast linkup capability.
Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.

]]> The following issues have been fixed in version 14.32.1010:

Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
The system could not create more than 128K QPs.
On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
Packet Pacing rate was used if asymmetric VFs was enabled.
Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.

]]> SR 2.9.0/SR 3.4.0 RC

]]>

Added support to save controller logs in host memory in the event of a system crash.

Added support for remote-managed SED rekey.

Added support for Configurable Spindown Spares policy.

Added support for the permanent disablement of unused IOBAR support in PCIe configuration space.

Enhance Redfish interfaces:

support DELETE for a Volume resource which is not the last created on a given array.
support DELETE for the last remaining Volume on an array which has SED encryption enabled.
support #Storage.ResetToDefaults with ResetType = ResetAll when encrypted volumes are present.
support AutoVolumeCreate property in Redfish Storage resource
support Links.Batteries property in Redfish StorageController resource

]]>

Fixed issues with the SED drive.

Fixed issues with the spare drive.

Fixed an issue with the SmartCache logical drive.

Fixed issues with expander firmware upgrade.

Fixed issues with RBOD devices.

Fixed a potential controller lockup issue while deleting a logical drive configuration on a controller.

Resolved an issue by allowing MCTP re-discovery exclusively during the first Bus Master Enable set.

Fixed UEFI HII unreadable characters in Chinese language.

Fixed an issue where WriteCacheProtected alert is sometimes not generated.

]]>

Fix for BSOD issue due to SRIS misdetection and FW Commit command via PCIe VDM (MCTP OVER PCIe) timed out.

]]>

Fix for BSOD issue due to SRIS misdetection and FW Commit command via PCIe VDM (MCTP OVER PCIe) timed out.

]]>

There are no enhancements in the current HPE iLO 5 v3.08 release

]]>

Fixed an issue where an SNMP query on cpqHoMIBStatusArray status failed post upgrade to HPE iLO 5 v3.00.

Fixed an issue where the drives in the Embedded SATA controller were displayed in the label of Un-configured Drives instead of Drives.

Fixed an issue where fetching the email ID for AD login users fails in a cross-domain setup, affecting the ability to send TFA tokens.

Fixed an issue that involves a fallback mechanism to retrieve the email address from the parent domain if it cannot be fetched from the cross-domain.

]]> iLO5 v 3.07 Fixes can be found atwww.hpe.com/support/ilo5-v3-07-Enhancements

]]> iLO5 v 3.07 Fixes can be found at www.hpe.com/support/ilo5-v3-07-Fixes

]]>

This product now supports the Link Layer Discovery Protocol (LLDP) on the VF.

This product now supports firmware logging via the debugfs.

This product now supports Red Hat Enterprise Linux 9 update 4.

]]> This product fixes an issue where the unexpected FW logs appears during some special environments, such as tx_timeout or NVM update.

]]>

This product now supports the Link Layer Discovery Protocol (LLDP) on the VF.

This product now supports firmware logging via the debugfs.

This product now supports Red Hat Enterprise Linux 9 update 4.

]]> This product fixes an issue where the unexpected FW logs appears during some special environments, such as tx_timeout or NVM update.

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]> Added value "C6 without C1E" in System Configuration (RBSU) option "Power Management/Advanced Power Options menu/Minimum Processor Idle Power Core C-State". When selected, the Minimum Processor Idle Power Core C-State is C6 with C1E disabled. This setting has the following Redfish property: /redfish/v1/systems/1/bios/MinProcIdlePower

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None

]]> This product enhanced to support Red Hat Enterprise Linux 9 update 5.

]]>

This product fixes an issue where VLAN set operation may leads to deadlock.

This product fixes an issue where a NULL pointer dereference in early reset.

This prodcut fixes an issue where users fail to change the number of queues (channels).

This product fixes an issue where system hang when VFs are created and VLAN configured.

]]> This product now supports FIPS-enabled mode.

]]> SR 2.9.0/SR 3.4.0 RC

]]> Support DL20 and ML30 Gen10 server.

New features and changes included in version 22.41.1000:

The new unified_fdb subdomain simplifies the FDB model by eliminating the need to duplicate rules for RX and TX tables. This domain is directionless, meaning no RX/TX specific actions are allowed. Firmware now handles packet transitions IN and OUT of the unified domain, allowing for a more streamlined packet flow management. Software can now transition between unified_fdb and FDB_RX/FDB_TX domains as long as the packet maintains the same direction, without the risk of dropping the packet when crossing between RX and TX.
Implemented Deterministic Random Bit Generator (DRBG) algorithm on top of firmware TRNG (the source for raw data input) in accordance with NIST SP800-90A.
Added support for vDPA virtual queue state change from suspend to ready, and discrete mkey for descriptor. vDPA Live Migration uses these two new capabilities to reduce downtime since vq can go back to ready state for traffic and descriptor-only-mkey can help reduce mkey mapping time.
Added the ability to generate up to 2^30 STE objects through the general object creation command.
Added a new NVConfig option to copy AR bit from the BTH header to the DHCP header.
Added the option to provide field's offset and length in Steering add_action option.
Added support for steering match on packet l4_type through FTG/FTE.
Extended Flex Parser merge mechanism to support hardware capabilities.
Enabled the option to disable the native parser when the parse graph node is configured with the same conditions.
Added support for father/son headers parsing.
Added support for tunnel_offload in LRO.

]]> The following issues have been fixed in version 22.41.1000:

GTP length field was automatically modified at the TX side when an incorrect or invalid length was detected.
Switch port would go down due to MC packets mirrored back to the switch when in promiscuous mode.
Traffic failure occurred when modifying the VIRTIO_NET_F_MRG_RXBUF bit for the VDPA device during traffic.
The second mkey index returned even if it was not set in the creation of the virtio q when querying virtio q object.
Traffic loss occurred after performing Live Migration with virtio vq "frozen-ready" feature.

Note: When the traffic load is high, and the vq frozen-ready cap is on, traffic loss might still be experienced after modifying the vq from suspend to ready mode.

New features and changes included in version 22.39.1002:

Modified the TCP IPv4 flows so that the steering TIR rx_hash_symmetric field is now valid only when both the SRC and DST fields are not set to zero.
Added a locking mechanism to protect the firmware from a race condition between insertion and deletion of the same rule in parallel. Such behavior occasionally resulted in firmware accessing a memory that has already been released, thus causing IOMMU / translation error.

Note: This change will not impact insertion rate for tables owned by SW steering.

Enabled live migration for virtio with mergeable buffer.
Added a caching mechanism to improved expansion ROM performance and to avoid any slow boot occurrences when loading the expansion ROM driver.
Added support for image size above 4GB when performing a live migration by splitting the image to chunks.
Extended the role-based authentication to cover all crypto algorithms. Now the TLS. IPsec. MACsec. GCM, mem2mem, and NISP work when nv_crypto_conf.crypto_policy = CRYPTO_POLICY_FIPS_LEVEL_2, meaning all cryptographic engines can also work in wrapped mode and not only in plaintext mode.
Programmable Congestion Control is now the default CC mechanism. ZTR_RTTCC is the default CC algorithm when ECE is enabled and the CC algorithm negotiation succeeds, otherwise PCC DCQCN will be used.
Added new support for reserved mkey index range. When enabled, a range of mkey indexes is reserved for mkey by name use.

]]> The following issues have been fixed in version 22.39.1002:

Migration data corruption occurred when running parallel save_vhca_state/load_vhca_state commands on the same PF.

]]> TBD

]]>

This product fixed error checking sequence for Firmware Management Protocol API.

This product fixed NC-SI commands to interoperate more benefit with iLO.

]]>

Updated supported environments

]]>

Updated SBOM requirement

]]> Support Microsoft Windows Server 2025

]]> Support HPE ProLiant DL145 Gen11 server.

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving the configuration page of an MR controller.

Addressed an issue where Windows Server 2025 HLK TPM2.0 UEFI Preboot Interface test failed on XL450 Gen10.

Addressed an issue where WHLK HSTI test failed.

Addressed an issue where the "Physical Drive missing" message appears twice in POST when a drive was removed and rebooted with incorrect severity in IML.

Addressed an issue where system may encounter an RSOD while updating the SAS drive FW via HPE Service Packs, including, but not limited to, VMware ESXi Online HDD FW Component Bundle 16.00, HPE Synergy Service Pack (SSP) 2024.01.02 (January 2024) and the future HPE Synergy Service Pack (SSP) 2024.07.01 (July 2024).

Known Issues:

None]]> Important Notes:

This revision of the System ROM includes the mitigation for security vulnerabilities CVE-2023-45229, CVE-2022-36763, CVE-2022-36764, CVE-2021-38578, CVE-2023-5678 and CVE-2024-0727. The security vulnerabilities are documented in the CVE report site. They are not unique to HPE servers. This version of the System ROM should be paired with Server Platform Services (SPS) Firmware 05.01.04.913.

Firmware Dependencies:

None

Enhancements/New Features:

Added value "C6 without C1E" in System Configuration (RBSU) option "Power Management/Advanced Power Options menu/Minimum Processor Idle Power Core C-State". When selected, the Minimum Processor Idle Power Core C-State is C6 with C1E disabled. This setting has the following Redfish property: /redfish/v1/systems/1/bios/MinProcIdlePower

Known Issues:

None]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

This setting has the following Redfish property:

/redfish/v1/systems/1/bios/settings/AmdIcConfigDisableITBypass

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving the configuration page of the MR controller.

Addressed an issue where Redfish BIOS actions, ResetBIOS and ChangePassword may not work.

Addressed an issue where Battery Failure IML message log may be incorrectly logged for the Smart Array controller with Smart Storage Battery.

Addressed an issue where system failed to boot with selected NVMe HDD by setting One-Time Boot Option in ILO Web.

Known Issues:

None]]> Important Notes:

This revision of the System ROM includes the mitigation for security vulnerabilities CVE-2023-31315 for AMD 2nd and 3rd Generation EPYC processors. This revision of the System ROM includes the mitigation for security vulnerabilities CVE-2023-45853, CVE-2023-45229, CVE-2022-36763, CVE-2022-36764, CVE-2023-5678, CVE-2021-38575 and CVE-2021-38578. The security vulnerabilities are documented in the CVE report site. They are not unique to HPE servers. This revision of the System ROM includes AMD reference code MilanPI 1.0.0.C for AMD 3rd Generation EPYC processors. This revision of the System ROM includes AMD reference code RomePI 1.0.0.H for AMD 2nd Generation EPYC processors.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the operating system could not detect iSCSI drive through IPv6 installation when iSCSI IpAddressType was set to auto. Addressed an issue where system would not complete POST after BIOS firmware updated to ver 3.00 with E810-XXVDA4's installed. Addressed an issue where system would hang with ASSERT during POST after adding DIMMs. Addressed an issue where the boot order was cleared unexpectedly after configuring System Configuration (RBSU) options, navigating to Boot Options > UEFI Boot Settings > UEFI Boot Order, and then pressing F12 to Save and Exit. Removed the value of "Not Specified" in System Configuration (RBSU) option "Server Security/Trusted Platform Module Options/Current TPM 2.0 Active PCRs" and set the default value as "SHA1 and SHA256".

Known Issues:

None]]> SR 2.9.0/SR 3.4.0 RC

]]>

Made changes to enhance the testability of the driver. Changes do not impact end customers.

]]>

Optimize sensor reporting to improve failure rate - AFR (Annual Failure Rate) metrics

]]>

Optimize sensor reporting to improve failure rate - AFR (Annual Failure Rate) metrics

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving the configuration page of an MR controller.

Addressed an issue where Windows Server 2025 HLK TPM2.0 UEFI Preboot Interface test failed on XL450Gen10.

Addressed an issue where the "Physical Drive missing" message appeared twice in POST when a drive was removed and rebooted with incorrect severity in IML.

Known Issues:

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None]]>

Added support for Microsoft Server Windows 2025.

]]>

Added support for Microsoft Server Windows 2022.

]]> This product enhanced the compatibility with the latest drivers.

]]>

This product now supports Red Hat Enterprise Linux 9 Update 3.

For more product details, please refer to the latest document in https://www.intel.com/content/www/us/en/download/19622/

This setting has the following Redfish property:

/redfish/v1/systems/1/bios/settings/AmdIcConfigDisableITBypass

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving configuration page of MR controller.

Addressed an issue where Redfish BIOS actions, ResetBIOS and ChangePassword may not work.

Addressed an issue that Battery Failure IML message log may be incorrectly logged for MR Controller with Smart Storage Battery.

Addressed an issue where system failed to boot with selected NVMe HDD by setting One-Time Boot Option in ILO Web.

Known Issues:

None]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the operating system could not detect iSCSI drive through IPv6 installation when iSCSI IpAddressType was set to auto.

Addressed an issue where system would not complete POST after BIOS firmware updated to ver 3.00 with E810-XXVDA4''s installed.

Addressed an issue where system would hang with ASSERT during POST after adding DIMMs.

Known Issues:

None]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

New OS support for RHEL9u3.

Support new HPE ProLiant DL145 Gen11 server.

]]> Fix an issue that kernel WARNING with call trace may be logged when server shut down/rebooted.

]]> New OS support for RHEL9u3.

]]> Fix an issue that kernel WARNING with call trace may be logged when server shut down/rebooted.

]]> TBD

]]> This product enhanced the compatibility with the new firmware.

]]> TBD

]]> This product enhanced the compatibility with VMware firmware component 1.34.0.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> This version is in compliance with IPU.2024.1 guidance.

]]> Important Notes:

Ver. 04.04.04.603(B) contains updates to the firmware packaging and is functionally equivalent to ver. 04.04.04.603. It is not necessary to upgrade with Revision B if a previous component revision was used to upgrade the firmware to version 04.04.04.603.

Firmware Dependencies:

None

Problems Fixed:

This revision of the Server Platform Services Firmware provides mitigations for security vulnerability documented as CVE-2023-35191. This issue is not unique to HPE servers.

Known Issues:

None

]]> This version is in compliance with IPU.2024.1 guidance.

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

This revision of the Server Platform Services Firmware provides mitigations for security vulnerability documented as CVE-2023-35191. This issue is not unique to HPE servers.

Known Issues:

None]]> This product enhanced the compatibility with drivers.

]]> This product addresses the issue of inconsistent metadata within the component products.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Updated SBOM requirement

]]>

Updated installation time

]]> This product enhanced the compatibility with drivers.

]]> This product addresses the issue of inconsistent metadata within the component products.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> The following fixes were incorporated in this version:

Temperature sensors logic inside gSEP model and SES database
When an IOM is pulled the surviving IOM reports false critical temperatures

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> The following fixes were incorporated in this version:

Temperature sensors logic inside gSEP model and SES database
When an IOM is pulled the surviving IOM reports false critical temperatures

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> TBD

]]> This product fixed an issue that caused the collecting minidump process to crash while the device was initializing.

]]> TBD

]]>

This product now supports Red Hat Enterprise Linux 8 update 9.

This product now supports FIPS-enabled mode.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

New release for version 7.726.02.00.

This new 7.26 release have not completed vSAN certification, please don’t update for vSAN environment for now. Target to complete vSAN certification by end of February 2024.

Support new HPE ProLiant DL145 Gen11 server.

]]> New release for version 7.726.02.00.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Support both Gen10P and Gen11 servers

]]> For Gen11 PR3 & 2023 March MSB

]]> TBD

]]> This product correct an issue which fixed an issue that VMs lose connectivity and system freezes with Windows Azure HCI.

]]>

Improve random read/write perfomance.

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving the configuration page of an MR controller.

Addressed an issue where Windows Server 2025 HLK TPM2.0 UEFI Preboot Interface test failed on XL450Gen10.

Addressed an issue where the "Physical Drive missing" message appeared twice in POST when a drive was removed and rebooted with incorrect severity in IML.

Known Issues:

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None]]>

Support both Gen10P and Gen11 servers

]]> Support both Gen10P and Gen11 servers

]]> Support FIPS mode.

]]>

Support HPE ProLiant DL180 Gen10 Server

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Added support for Microsoft Server Windows 2025.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]> Firmware for the following devices has been updated to 14.32.1010:

817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)

Firmware for the following device has been updated to 16.35.3502:

874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)

New features and changes included in firmware version 14.32.1010:

Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
Limited the external loopback speed to the used module's capabilities.
Improved linkup time when using the fast linkup capability.
Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.

New features and changes included in firmware version 16.35.3502:

Modified the TCP IPv4 flows so that the steering TIR rx_hash_symmetric field is now valid only when both the SRC and DST fields are not set to zero.

]]> The following issues have been fixed in firmware version 14.32.1010:

Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
The system could not create more than 128K QPs.
On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
Packet Pacing rate was used if asymmetric VFs was enabled.
Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.

No fixes are included in firmware version 16.35.3502.

]]> Firmware for the following devices has been updated to 2.42.5044 :

779799-B21 (HPE Ethernet 10G 2-port 546FLR-SFP+ Adapter)
779793-B21 (HPE Ethernet 10G 2-port 546SFP+ Adapter)

Firmware for the following devices has been updated to 14.32.1010:

817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)

Firmware for the following device has been updated to 16.35.3006:

874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)

New Features and changes included in version 1.0.20(A):

Version 1.0.20(A) has been recompiled to create the firmware RPM compatible with RPM LIB v4.14.2. As a result, this rebuild firmware version 1.0.20(A) can now be installed successfully on a node with FIPS enabled.

New features and changes included in version 14.32.1010:

Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
Limited the external loopback speed to the used module's capabilities.
Improved linkup time when using the fast linkup capability.
Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.

New features and changes included in version 16.35.3006:

Enabled ACS for single port cards.
Added vPort counters after creating the LAG demux table to count kernel packets reaching all the PFs participating in the LAG.

]]> The following issues have been fixed in version 2.42.5044 :

An issue that prevented the firmware from detecting a link_down event thus preventing the IB bond interface from going to a failover mode.

The following issues have been fixed in version 14.32.1010:

Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
The system could not create more than 128K QPs.
On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
Packet Pacing rate was used if asymmetric VFs was enabled.
Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.

The following issues have been fixed in version 16.35.3006:

Packet loss that occurred when restarting the transmit.
An issue that prevented RoCE malformed packets (UDP packet with dest_port equal to RoCE well known udp_dport (0x4791)) from being counted on the vport_counter when the function disables RoCE (through MODIFY_NIC_VPORT_CONTEXT command).
A memory leakage that occurred when closing connected QPs (Type RC/UC/XRC/DC).
Added a missing VLAN strip.

]]> Support SHA384

]]>

Added support for Microsoft Server Windows 2025.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]> Support Microsoft Windows Server 2025

]]> Support HPE ProLiant DL145 Gen11 server.

]]>

Corrective actions to fix potential background media scan issue.

]]>

Corrective actions to fix potential background media scan issue.

]]> Important Notes:

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2024.1 guidance.

Known Issues:

None]]> Important Notes:

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2024.1 guidance.

Known Issues:

None]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Added support for Microsoft Windows Server 2025.

]]>

Added support for Microsoft Windows Server 2022.

]]>

Fix for Uncorrectable Machine Check Exception (UMCE) issue which might occur.

]]>

Fixed CA https://support.hpe.com/hpesc/public/docDisplay?docId=emr_na-a00126514en_us

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Updated Supported Environments

]]>

Updated SBOM requirement

]]> Important Notes:

This revision of the System ROM includes the mitigation for security vulnerabilities CVE-2023-31315 for AMD 1st and 2nd Generation EPYC processors. This revision of the System ROM includes the mitigation for security vulnerabilities CVE-2023-45853, CVE-2023-45229, CVE-2022-36763, CVE-2022-36764, CVE-2021-38578, CVE-2023-5678 and CVE-2024-0727. The security vulnerabilities are documented in the CVE report site. They are not unique to HPE servers. This revision of the System ROM includes AMD reference code NaplesPI 1.0.0.L for AMD 1st Generation EPYC processors. This revision of the System ROM includes AMD reference code RomePI 1.0.0.H for AMD 2nd Generation EPYC processors.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the operating system could not detect iSCSI drive through IPv6 installation when iSCSI IpAddressType was set to auto.

Known Issues:

None]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> Updated to version 1.0.0.1

]]> TBD

]]> This product enhanced libtool macros warning message for new OS distribution.

]]> This product fixed compliant with rdma-core v24.

]]> Important Notes:

None

Firmware Dependencies:

For HPE ProLiant Gen10 Plus servers, iLO5 version 2.55 or above is required to upgrade to this version.

Enhancements/New Features:

Changed certain behaviors to avoid machine power failures when significant power consumption devices are introduced.

Problems Fixed:

None

Known Issues:

None

]]> Important Notes:

None

Firmware Dependencies:

For HPE ProLiant Gen10 Plus servers, iLO5 version 2.55 or above is required to upgrade to this version.

Enhancements/New Features:

Changed certain behaviors to avoid machine power failures when significant power consumption devices are introduced.

Problems Fixed:

None

Known Issues:

None

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> This product added support to new Gen11 and Gen12 servers.

]]> This product enhanced the compatibility with firmware of Fortville 9.4.

]]>

Added support for Microsoft Server Windows 2025.

]]>

Mitigates the potential drive FW halt issue.

]]> irmware for the following devices has been updated to 12.28.2006:

843400-B21 (HPE Apollo A10 InfiniBand EDR (100Gb) 2-port Adapter)

Firmware for the following devices has been updated to 16.35.3006:

872723-B21 (HPE Apollo InfiniBand EDR 100Gb 2-port 841z Mezzanine Adapter)
872725-B21 (HPE InfiniBand EDR 100Gb 1-port 841QSFP28 Adapter)

New features and changes included in version 1.0.0.14:

Added firmware flash support on Microsoft Windows Server 2025.

New features and changes included in version 12.28.2006:

Increased the maximum XRQ number to 512.

New features and changes included in version 16.35.4030:

Added support for postponing QP timeout "retry exceeded" errors for traffic directed at specific destinations. This new capability prevents broken connections for destinations in downtime because of live migration.

]]> The following issues have been fixed in firmware version 12.28.2006:

Fixes an issue that caused the DCR to be destroyed before the retry option managed to work when the retry timeout is too big. In this case the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
Increased PHY power consumption limit to 1.5w.
Fixed an issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.

The following issues have been fixed in version 16.35.4030:

VF FLR would get stuck when its PF triggered the FLR as well.
Unexpected source UDP port appeared in RoCE packets when the firmware ignored a non-PF driver configuration for RoCE source UDP port control (as set in SET_HCA_CAP.sw_r_roce_src_udp_port).

]]> Firmware for the following devices has been updated to 12.28.2006:

843400-B21 (HPE Apollo A10 InfiniBand EDR (100Gb) 2-port Adapter)

Firmware for the following devices has been updated to 16.35.3006:

872723-B21 (HPE Apollo InfiniBand EDR 100Gb 2-port 841z Mezzanine Adapter)
872725-B21 (HPE InfiniBand EDR 100Gb 1-port 841QSFP28 Adapter)

New features and changes included in version 12.28.2006:

Increased the maximum XRQ number to 512.

New features and changes included in version 16.35.3006:

Enabled ACS for single port cards.
Added vPort counters after creating the LAG demux table to count kernel packets reaching all the PFs participating in the LAG.

]]> Fixes in version 12.28.2006:

Fixed an issue that caused the DCR (DC Resources) to be destroyed before the retry option managed to work when the retry timeout is too big. in this case, the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
Increased PHY power consumption limit to 1.5w.
Fixed an issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.

The following issues have been fixed in version 16.35.3006:

Packet loss that occurred when restarting the transmit.
An issue that prevented RoCE malformed packets (UDP packet with dest_port equal to RoCE well known udp_dport (0x4791)) from being counted on the vport_counter when the function disables RoCE (through MODIFY_NIC_VPORT_CONTEXT command).
A memory leakage that occurred when closing connected QPs (Type RC/UC/XRC/DC).
Added a missing VLAN strip.

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving the configuration page of an MR controller.

Addressed an issue where Windows Server 2025 HLK TPM2.0 UEFI Preboot Interface test failed on XL450 Gen10.

Addressed an issue where WHLK HSTI test failed.

Addressed an issue where the "Physical Drive missing" message appears twice in POST when a drive was removed and rebooted with incorrect severity in IML.

Known Issues:

None]]> Important Notes:

Firmware Dependencies:

None

Enhancements/New Features:

Known Issues:

None]]>

This firmware version fixes a bug with the unmap command that may cause a drive hang

]]> See the AMS Release Notes for information about the enhancements in this release.

]]> See the AMS Release Notes for information about the issues resolved in this release.

]]> The SLES15 AMS rpm is now FIPS compliant

]]> Fixed the following items:

Fixed the issue where AMS was crashing after plugging and removing a USB drive

]]> Added support for Microsoft Server Windows 2025.

]]>

Fix for BSOD issue due to SRIS misdetection and FW Commit command via PCIe VDM (MCTP OVER PCIe) timed out.

]]>

Fix for BSOD issue due to SRIS misdetection and FW Commit command via PCIe VDM (MCTP OVER PCIe) timed out.

]]>

Fixes an issue in previous version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on

]]>

Fixes an issue in previous version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on

]]>

Maintenance firmware release to introduce fixes from previous firmware.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

It has fix code for V6 read disturb and other issues.

For more information, refer to HPE Customer Bulletin at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00136659en_us

]]> It has fix code for V6 read disturb and other issues

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> * An error was found in the queue fullhandling process that results in the FUA bit not getting properly set, which could lead to the drive self-initiated reset

* The FW fix is to resolve the handling of FUA bit during the queue full handling process has been implemented

]]> Added support for Microsoft Server Windows 2025.

]]>

Optimize sensor reporting to improve failure rate - AFR (Annual Failure Rate) metrics

]]>

Optimize sensor reporting to improve failure rate - AFR (Annual Failure Rate) metrics

]]> Firmware for the following devices has been updated to 12.28.2006:

825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)

Firmware for the following devices has been updated to 16.35.3006:

879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)
872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)

New Features and changes included in version 12.28.2006:

Increased the maximum XRQ number to 512.

New features and changes included in version 16.35.4030:

Added support for postponing QP timeout "retry exceeded" errors for traffic directed at specific destinations. This new capability prevents broken connections for destinations in downtime because of live migration.

]]> The following issues have been fixed in firmware version 12.28.2006:

Fixes an issue that caused the DCR to be destroyed before the retry option managed to work when the retry timeout is too big. In this case the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
Increased PHY power consumption limit to 1.5w.
Fixed an issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.

The following issues have been fixed in version 16.35.4030:

VF FLR would get stuck when its PF triggered the FLR as well.
Unexpected source UDP port appeared in RoCE packets when the firmware ignored a non-PF driver configuration for RoCE source UDP port control (as set in SET_HCA_CAP.sw_r_roce_src_udp_port).

]]> Firmware for the following devices has been updated to 12.28.2006:

825110-B21 (HPE InfiniBand EDR/Ethernet 100Gb 1-port 840QSFP28 Adapter)
825111-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 840QSFP28 Adapter)

Firmware for the following devices has been updated to 16.35.3006:

879482-B21 (HPE InfiniBand FDR/Ethernet 40/50Gb 2-port 547FLR-QSFP Adapter)
872726-B21 (HPE InfiniBand EDR/Ethernet 100Gb 2-port 841QSFP28 Adapter)

New Features and changes included in version 1.0.15(A):

Version 1.0.15(A) has been recompiled to create the firmware RPM compatible with RPM LIB v4.14.2. As a result, this rebuild firmware version 1.0.15(A) can now be installed successfully on a node with FIPS enabled.

New Features and changes included in version 12.28.2006:

Increased the maximum XRQ number to 512.

New features and changes included in version 16.35.3006:

Enabled ACS for single port cards.
Added vPort counters after creating the LAG demux table to count kernel packets reaching all the PFs participating in the LAG.

]]> The following issues have been fixed in component version 1.0.15(B):

Transaction test error was reported while deploying the component using SPP from HPE Linux SDR.

The following issues have been fixed in firmware version 12.28.2006:

Fixes an issue that caused the DCR to be destroyed before the retry option managed to work when the retry timeout is too big. In this case the DCR' time-to-live was increased, and the maximum retry timeout was decreased.
Increased PHY power consumption limit to 1.5w.
Fixed an issue that caused PortCounters.PortRcvErr / PPCNT.infiniband_counters.PortRcvErr not to report port icrc errors.

The following issues have been fixed in firmware version 16.35.3006:

Packet loss that occurred when restarting the transmit.
An issue that prevented RoCE malformed packets (UDP packet with dest_port equal to RoCE well known udp_dport (0x4791)) from being counted on the vport_counter when the function disables RoCE (through MODIFY_NIC_VPORT_CONTEXT command).
A memory leakage that occurred when closing connected QPs (Type RC/UC/XRC/DC).
Added a missing VLAN strip.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

It has fix code for V6 Read disturb issue and other issue.

For more information, refer to HPE Customer Bulletin at the following URL: https://support.hpe.com/hpesc/public/docDisplay?docId=a00136659en_us

]]> It has fix code for V6 Read disturb issue and other issue

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> TBD

]]> This product enhanced the compatibility with firmware of Fortville 9.3.

]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU.2023.3 guidance.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2023.3 guidance.

Known Issues:

None

]]> Important Notes:

This version of the Server Platform Services (SPS) Firmware contains updates aligned with the Intel Product Update (IPU) version IPU.2023.3 guidance.

Firmware Dependencies:

None

Enhancements/New Features:

This version is in compliance with IPU.2023.3 guidance.

Known Issues:

None

]]> 2024 Sep MSB

]]>

Added command to support the erasure of logs and events stored in the controller.

Added command to support spare spin down policy setting if the feature is supported.

]]>

Fixed issue of ADU report generation when using SSADUESXI within the VMWare ESXi system.

Fixed the display issue with physical drives in the enclosure under the multipath configuration.

Fixed issue where the tool allowed the Heal array operation on RMSED secured arrays when KMS is not active.

Fixed issue where the tools would allow users to attempt Change Drive Type operations with 512/512e drives for 4Kn logical volumes.

Fixed issue where users specified an incorrect encryption mode for a logical volume that did not match the existing mode on the array.

Fixed issue where the operation to revert the SEDs to Original Factory State (OFS) was not being blocked when KMS is not available in remote SED mode.

Fixed the volume creation issue when users specify the 'volatileencryptionkey' option while the Controller setting does not support it.

Fixed issue of error message occurring when using the 'create type=arrayR0' command with 'drives=' and 'drivetype=' options.

Fixed installation issue encountered when attempting to downgrade SSACLI from versions 6.30.X.X to 6.15.X.X or 6.20.X.X.

]]> TBD

]]> This product now supports additional snapdump driver logs.

]]>

This product fixed system failure when both NPAR and more than supported VFs through Driver with SR-IOV information in.

This product fixed rx-ring size less than 256 use case to cause PSOD.

This product fixed checksum issues for tunnel packets in ENS mode.

This product fixed BFD control failures in NSX environment.

]]>

Updated supported environments

]]>

Updated SBOM requirement

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving the configuration page of an MR controller.

Addressed an issue where Windows Server 2025 HLK TPM2.0 UEFI Preboot Interface test failed on XL450Gen10.

Addressed an issue where the "Physical Drive missing" message appeared twice in POST when a drive was removed and rebooted with incorrect severity in IML.

Known Issues:

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving the configuration page of an MR controller.

Addressed an issue where Windows Server 2025 HLK TPM2.0 UEFI Preboot Interface test failed on XL450 Gen10.

Addressed an issue where WHLK HSTI test failed.

Addressed an issue where the "Physical Drive missing" message appears twice in POST when a drive was removed and rebooted with incorrect severity in IML.

Known Issues:

None]]> Important Notes:

Firmware Dependencies:

None

Enhancements/New Features:

Known Issues:

None]]>

Added support for Microsoft Server Windows 2025.

]]>

Corrective actions to fix potential background media scan issue.

]]>

Corrective actions to fix potential background media scan issue.

]]> Added DL145 Gen11 server & DL380a Gen12 server support

]]> New release for version 007.2613.0000.0000.

]]>

Corrective actions to fix potential background media scan issue.

]]>

Corrective actions to fix potential background media scan issue.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Added support for Microsoft Windows Server 2022.

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]> The following enhancement has been added in this version:

Added support of RHEL 8.7
Added support of RHEL 9.1
Added support of SLES15 SP4

]]> The following fixes were incorporated in this version:

Smart Array reporting "Storage Enclosure FW upgrade Problem Detected".
PSU version is showing as "No Ver" after inserted the New bel power PSU.
GEM_5_2 Coverity defect fix.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> The following enhancement has been added in this version:

Added support of Rhel 7.8
Added support of Rhel 8.2
Added support of SLES15 SP2

]]> The following fixes were incorporated in this version:

Smart Array reporting "Storage Enclosure FW upgrade Problem Detected".
PSU version is showing as "No Ver" after inserted the New bel power PSU.
GEM_5_2 Coverity defect fix.

Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

]]> This product carries SBOM signatures.

]]> Supports VMware ESXi 8.0

]]> See the AMS Release Notes for information about the enhancements in this release.

]]> See the AMS Release Notes for information about the issues resolved in this release.

]]> The RHEL8 AMS rpm is now FIPS compliant

]]> Fixed the following items:

Fixed the issue where AMS was crashing after plugging and removing a USB drive

]]>

Added support for Microsoft Windows Server 2025.

]]>

Added support for Microsoft Windows Server 2022.

]]> This is the first driver for Windows 2025 . The driver version is 9.4.10.20.

]]>

Updated driver

Added support for Windows Server 2025

Updated supported platforms

]]>

Driver update

]]> Added support for:

RedHat Enterprise Linux 8.10

RedHat Enterprise Linux 9.4

SUSE Linux Enterprise Server 15.6

Updated to driver version 10.02.12.01-k1

]]> Added support for:

RedHat Enterprise Linux 8.9

RedHat Enterprise Linux 9.3

Updated to driver version 10.02.11.00-k1

]]> TBD

]]>

This product now supports multiple RSS contexts via ethtool.

This product enhanced driver resource management and optimization to avoid driver crash.

]]>

This product fixed kernel NULL pointer dereference after AER with roce driver reload.

This product fixed kernel call trace observed while running nfs over rdma.

This product fixed kernel panic when running ptp4l along with certain traffic.

This product fixed kernel panic while unloading roce driver with one MSI-X vector.

]]> SR 2.9.0/SR 3.4.0 RC

]]>

Fixed issue where the OS retained the size of the original logical drive after a logical drive size expansion operation, occurring under very rare conditions.

]]> SR 2.9.0/SR 3.4.0 RC

]]>

Made changes to enhance the testability of the driver. Changes do not impact end customers.

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving the configuration page of an MR controller.

Addressed an issue where Windows Server 2025 HLK TPM2.0 UEFI Preboot Interface test failed on XL450Gen10.

Addressed an issue where the "Physical Drive missing" message appeared twice in POST when a drive was removed and rebooted with incorrect severity in IML.

Known Issues:

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None]]> Added support for:

Red Hat Enterprise Linux 8.10

Red Hat Enterprise Linux 9.4

SuSE Linux Enterprise Server 15.6

Updated to version 14.4.329.9

]]> Added support for:

Red Hat Enterprise Linux 8.10

Red Hat Enterprise Linux 9.4

SUSE Linux Enterprise Server 15sp6

Updated to version 14.2.589.33

]]>

Initial version for UBM FWPKG.

Support RHEL9 and ESXi8.0

]]>

Initial version for UBM FWPKG.

Support RHEL9 and ESXi8.0

]]> Firmware for the following devices has been updated to 14.32.1010:

817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)

Firmware for the following device has been updated to 16.35.3502:

874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)

New features and changes included in firmware version 14.32.1010:

Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
Limited the external loopback speed to the used module's capabilities.
Improved linkup time when using the fast linkup capability.
Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.

New features and changes included in firmware version 16.35.3502:

Modified the TCP IPv4 flows so that the steering TIR rx_hash_symmetric field is now valid only when both the SRC and DST fields are not set to zero.

New features and changes included in version 1.0.0.21(A):

Added firmware flash support on Microsoft Windows Server 2025.

]]> The following issues have been fixed in firmware version 14.32.1010:

Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
The system could not create more than 128K QPs.
On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
Packet Pacing rate was used if asymmetric VFs was enabled.
Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.

No fixes are included in firmware version 16.35.3502.

]]> Firmware for the following devices has been updated to 14.32.1010:

817749-B21 (HPE Ethernet 25Gb 2-port 640FLR-SFP28 Adapter)
817753-B21 (HPE Ethernet 25Gb 2-port 640SFP28 Adapter)

Firmware for the following device has been updated to 16.35.3502:

874253-B21 (HPE Ethernet 100Gb 1-port 842QSFP28 Adapter)

New features and changes included in firmware version 14.32.1010:

Added 3 new assert filters (Health buffer, NVlog, FW trace). The assert will be exposed now if its severity level is equal to or above the new filter.
Enabled Rate Limit per VM instead of VM-TC. This capability is implemented by adding support to a new Scheduling element type: rate limit elements that will connect to the rate_limit and will share its rate limit.
Added support for asymmetrical VFs per PF. To enable it:PF_NUM_OF_VF_VALID must be true, and PF_NUM_OF_VF to a non-zero value.
Limited the external loopback speed to the used module's capabilities.
Improved linkup time when using the fast linkup capability.
Added support for the slow_restart and slow_restart_idle parameters to enable Zero Touch RoCE capability.

New features and changes included in firmware version 16.35.3502:

Modified the TCP IPv4 flows so that the steering TIR rx_hash_symmetric field is now valid only when both the SRC and DST fields are not set to zero.

]]> The following issues have been fixed in firmware version 14.32.1010:

Firmware got into an unresponsive state and caused unexpected behavior when connecting an optical transceiver that support RxLOS and the remote side port was down.
The system could not create more than 128K QPs.
On rare occasions, the system got into an unresponsive state when a peer port went down while using an Optical module.
Packet Pacing rate was used if asymmetric VFs was enabled.
Incorrect RNR timeout when trying to set it during the rts2rts_qp transition.
Issue with RSS on IPSec flows in ConnectX-4 Lx led to performance degradation. In this scenario, the SPI optimization caused packets from a given host to hash to the same CPU core. The fix was to ignore SPI optimization according to l4_type in ConnectX-4 Lx adapter cards.
The GetInventory NC-SI command reported leading 0xf in firmware version when it started with 0.

No fixes are included in firmware version 16.35.3502.

]]>

Added support for Microsoft Server Windows 2025.

]]>

Added support for Microsoft Server Windows 2022.

]]> This product introduced power restrictions of 4.5 watts per port.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

]]>

This product addressed an issue where Network Interface initialization failure under OS or Firmware rollback may be seen with LLDP enabled.

This product addressed an issue where RDE PermanentMACAddress changes simultaneously when send PATCH request for MACAddress property with Firmware 4.30.

]]> Important Notes:

Ver. 0.2.3.0(B) contains updates to the firmware packaging and is functionally equivalent to ver. 0.2.3.0. It is not necessary to upgrade with Revision B if a previous component revision was used to upgrade the firmware to version 0.2.3.0.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where Innovation Engine (IE) may improperly reset every 24 hours. On some systems this could result in a brief drop in CPU utilization or network traffic lasting less than a second.

Known Issues:

None

]]> Important Notes:

None

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None

]]> TBD

]]>

This product now supports Red Hat Enterprise Linux 9 Update 3.

For more product details, please refer to the latest document in https://www.intel.com/content/www/us/en/download/19622/

This setting has the following Redfish property:

/redfish/v1/systems/1/bios/settings/AmdIcConfigDisableITBypass

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving configuration page of MR controller.

Addressed an issue where Redfish BIOS actions, ResetBIOS and ChangePassword may not work.

Addressed an issue that Battery Failure IML message log may be incorrectly logged for MR Controller with Smart Storage Battery.

Addressed an issue where system failed to boot with selected NVMe HDD by setting One-Time Boot Option in ILO Web.

Known Issues:

None]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where the operating system could not detect iSCSI drive through IPv6 installation when iSCSI IpAddressType was set to auto.

Addressed an issue where system would not complete POST after BIOS firmware updated to ver 3.00 with E810-XXVDA4's installed.

Addressed an issue where system would hang with ASSERT during POST after adding DIMMs.

Addressed an issue where the boot order was cleared unexpectedly when configuring System Configuration (RBSU) options with certain steps.

Known Issues:

None]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> Added support for:

RedHat Enterprise Linux 8.10

RedHat Enterprise Linux 9.4

SUSE Linux Enterprise Server 15.6

Updated to driver version 10.02.12.01-k1

]]> Added support for:

RedHat Enterprise Linux 8.9

RedHat Enterprise Linux 9.3

Updated to driver version 10.02.11.00-k1

This Driver is FIPS enabled.

]]> This Driver is FIPS enabled.

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]>

Optimize sensor reporting to improve failure rate - AFR (Annual Failure Rate) metrics

]]>

Optimize sensor reporting to improve failure rate - AFR (Annual Failure Rate) metrics

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]>

Added support for VMware 8.0

]]>

Added support for VMware 8.0

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fixed flashing issue through SDR method

]]>

Fixed flashing issue through SDR method

]]> Important Notes:

Ver. 0.2.3.0(E) contains updates to the firmware packaging and is functionally equivalent to ver. 0.2.3.0. It is not necessary to upgrade with Revision E if a previous component revision was used to upgrade the firmware to version 0.2.3.0.

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None

]]> Important Notes:

Ver. 0.2.3.0(C) contains updates to the firmware packaging and is functionally equivalent to ver. 0.2.3.0. It is not necessary to upgrade with Revision B if a previous component revision was used to upgrade the firmware to version 0.2.3.0.

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None

]]> Important Notes:

This version of the System ROM contains updates aligned with the Intel Product Update (IPU) version IPU.2024.3 guidance.

Firmware Dependencies:

None

Problems Fixed:

Addressed an issue where NS204i may not be identified as an NVMe device.

Addressed an issue where the Logical Drive name was cleared in RBSU after leaving configuration page of an MR controller.

Addressed an issue that Battery Failure IML message log may be incorrectly logged for MR Controller with Smart Storage Battery.

Addressed an issue where system failed to boot with selected NVMe HDD by setting One-Time Boot Option in ILO Web.

Known Issues:

None]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None]]> Important Notes:

Ver. 0.2.3.0(C) contains updates to the firmware packaging and is functionally equivalent to ver. 0.2.3.0. It is not necessary to upgrade with Revision C if a previous component revision was used to upgrade the firmware to version 0.2.3.0.

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None

]]> Important Notes:

Firmware Dependencies:

None

Problems Fixed:

Known Issues:

None

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Added support for Microsoft Server Windows 2025.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Fix component SAS core dump issue which along with NVMe drives behind MR controllers on certain platform flashing.

Fix NVMe drive component failed to update problem behind more than 2 MR controllers on certain platform.

Fix NVMe drive component which shows wrong behavior message against the flash result.

Fix SPP force upgrade flash component problem on certain drive family.

]]>

Added support for Microsoft Windows Server 2025.

]]>

Added support for Microsoft Windows Server 2022.

]]>

This product enhances the core-dump missing a few entries.

This product enhances the Hardware CoS queue re-configuration between ifdown/ifup.

This product enhances to add support for enable/disable RDMA to NCSI command NcsiCmd_Set_Partition_Cfg_cmd function.

This product enhances to add support store PLDM Monitoring and Control events before BMC's SetEventReceiver command.

This product addresses an issue where Tx timeout detected in dmesg while running L2 traffic with 9600 MTU.

]]>

This product addresses an issue where RDE Port LLDPReceive ManagmentAddressMAC returned empty string when it's not present.

This product addresses an issue where Ethtool shows wrong module type when a port is in a certain breakout mode.

This product addresses an issue where in low temperature test, BMC reading module temperature result is 0xff.

This product addresses an issue where failure to set default values for firmware speed capabilities.

This product enhances support for loopback port statistics via HWRM (Hardware Resource Manager).

This product addresses an issue where flow control status in dmesg shows wrong TX and RX negotiated status.

This product addresses an issue where fixed bnxtnvm to verify the VPD data before writing to the NVM.

This product addresses an issue where ping failures between allmulticast enabled VFs.

This product addresses where the RoCE protocol's read_context function in the HWRM (Hardware Resource Manager) component was failing when dealing with the Completion Queue.