Driver version 5.4.81.2_1

]]> Driver version 5.4.80.0

]]>
  • Improves data integrity
  • Decreases possibility of data corruption in certain error and timing conditions
  • Reduces the probability of hangs
    • ]]>
  • Updated supported platforms
    • ]]>
  • Added support for Intel platforms
    • ]]>         New features and changes in driver version 4.22.73.1004:

    • Firmware CR dump will now be collected automatically into ZDUMP PSOD or on livedump for debuggability purposes.
    • Enabled the driver to read the temperature from private statistics.

    To see the temperature, run:# nsxdp-cli ens uplink stats get -n vmnic1 | grep -i asicSensorTemperature

    • Added support for Hardware Accelerated GENEVE and VXLAN encapsulation and decapsulation for RoCE traffic.
    • Hardware accelerated flows can now be mirrored using the standard packet capture tools.
    • Added the ability to offload NSX Distributed Firewall rules by using in-hardware tracking of packet flows.
    • RSS support for ENS Model 1 improves performance using fewer CPU cores. This capability can be enabled using the "netq_rss_ens" module parameter.
    ]]>         Fixes included in driver version 4.22.73.1004:

    • Fixed an issue that caused a ParaVirtual VM to lose traffic after resuming from the suspend mode when SR-IOV was enabled in the system.
    • Cleaned steering rule from FDB when VF is being quiesced.
    • Fixed an issue that caused the driver to configure the incorrect SL value for RoCE with RDMACM.
    ]]>         New features and changes in driver version 4.22.73.1004:

    • Firmware CR dump will now be collected automatically into ZDUMP PSOD or on livedump for debuggability purposes.
    • Enabled the driver to read the temperature from private statistics.

    To see the temperature, run:# nsxdp-cli ens uplink stats get -n vmnic1 | grep -i asicSensorTemperature

    • Added support for Hardware Accelerated GENEVE and VXLAN encapsulation and decapsulation for RoCE traffic.
    • Hardware accelerated flows can now be mirrored using the standard packet capture tools.
    • Added the ability to offload NSX Distributed Firewall rules by using in-hardware tracking of packet flows.
    • RSS support for ENS Model 1 improves performance using fewer CPU cores. This capability can be enabled using the "netq_rss_ens" module parameter.
    ]]>         Fixes included in driver version 4.22.73.1004:

    • Fixed an issue that caused a ParaVirtual VM to lose traffic after resuming from the suspend mode when SR-IOV was enabled in the system.
    • Cleaned steering rule from FDB when VF is being quiesced.
    • Fixed an issue that caused the driver to configure the incorrect SL value for RoCE with RDMACM.
    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This is the initial version of the firmware.

    Known Issues:

    None

    ]]>
  • Improve the FW about data mismatch after SPL
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • This product now changes default number of queues for high core count platforms
  • This product changes the default setting where the GNSS(GNSS_SUPPORT) is disabled now
  • This product now supports RHEL 8.7
    • ]]>
  • This product fixes an issue where the virtual function failed to create
  • This product fixes an issue where crash is observed when changing the bonding mode from Balance TLB to 802.3ad
  • This product fixes an issue where the traffic goes to unintended random rx_queues when number of parallel stream increased in iperf even if affinity is set
    • ]]>         This product enhanced the availability of debugfs functionality when UEFI Secure Boot is enabled

    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         This product now supports  ResetToDefault property(RDE Port Schema).

    ]]>         This product addresses an issue where InterfaceEnabled property is read only and it can't patch this property

    ]]>
  • This product now supports RDE Read and Write operations.
  • This product now supports Debug Dump feature.
  • This product now supports new parameters when software requesting on Port 0(via AQ the connectivity type)
    • ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>
  • DMTF PLDM Redfish Device Enablement enhancements
    • Support Volume Creation and Deletion by the following Redfish requests
      • POST VolumeCollection
      • DELETE Volume
      • GET Volume Capabilities
    • Added support for the following Redfish ACTION requests:
      • POST Storage.ResetToDefaults
      • POST Volume.Initialize
      • POST Drive.SecureErase
    • Added support for Redfish PATCH requests for the following properties:
      • PATCH Volume.DedicatedSpareDrives
      • PATCH Volume.DisplayName
      • PATCH Volume.ReadCachePolicy
      • PATCH Volume.WriteCachePolicy
      • PATCH Drive.HotspareType
      • PATCH Drive.LocationIndicatorActive
      • PATCH Drive.WriteCacheEnabled
  • Support DMTF PLDM firmware update for drive
    • ]]>
  • Fix a00127934en_us: HPE ProLiant Gen10 Plus Servers - Unable to Switch From LKM to EKM With MR Controllers When Boot Time Password is Set
  • Fix an issue that Sanitize Block Erase on NVMe drive along with shutdown sequence may cause assertion in firmware.
  • Fix an issue that GET Volume query from REST client may fail when multiple Volumes are configured on the controller
  • Fix an issue that firmware throws error when setting WCE (Disk Write Cache) = 0 for JBOD drive.
  • Fix an issue that HDD sensor shows temperature on 14-HD Max when there is no drive installed.
  • Fix an issue that HII page may hang while there is pinned cache then do drives initialization and View Server Profile.
  • Fix a rare issue that controller may not getting discovered when there is power loss during cache restoration from a previous power loss.
  • Fix an issue that controller may hang and Online Controller Reset is triggered after running "storcli /cx set debug reset all" and then "storcli /cx get snapdump".
  • Fix an issue that enable security on logical drive may enable security on other unrelated drives which were configured as Dedicated Spare drive for other secured logical drive before.
  • Fix an issue that drive running sanitize overwrite may become Unconfigured Bad Unsupported after a cold boot
  • Fix a rare issue that firmware may hit assertion failure when a drive causes IO issue and fails.
  • Fix an issue that IML 1906 may be incorrectly logged when doing config clear and reboot.
  • Fix an issue that NVMe drives may move to Unconfigured Bad state from Unconfigured Good during driver unload-reload.
  • Fix an issue that SPDM GET_MEASUREMENTS command signature verification is failing at iLO
    • ]]>         This Firmware package contains following firmware versions:

    Adapter

    Speed

    MBI

    Firmware

    UEFI

    Boot Bios
    HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter 32Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter 32Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter 64Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter 64Gb 02.08.05 09.12.01 7.34 0.0

    Non-disruptive firmware upgrades: non-disruptive firmware updates is enabled and will not require a server reboot to apply.

    ]]>         Fixed the following behavior:

    Temperature Misreading: the adapter was reading incorrect reading of the temperature on the HPE SN1610Q 32Gb Fibre Channel Host Bus adapter's Small Form-factor Pluggable. The symptom would result in a temperature spike and potentially reset the system

    ]]>         This Firmware package contains following firmware versions:

    Adapter

    Speed

    MBI

    Firmware

    UEFI

    Boot Bios
    HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter 32Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter 32Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter 64Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter 64Gb 02.07.06 09.09.20 7.28 0.0
    ]]>         The Firmware fixes the following:

    • Unsuccessful read of the SFP Temperature which will trigger a Server Shutdown. 
    • Message related to a Mailbox 0x48 Firmware dump saved to buffer.
    ]]>         The following changes and new features have been included in version 23.04-1.1.3.1

    • Starting this release, MLNX EN+RoCE drivers will adopt the following versioning naming scheme: YY.MM-x.x.x.x (i.e., Year.Month-x.x.x.x).
    • Added support for allowing the host to track various statistics for the VFs, specifically all of the Q_counters stats even if he gives the VF to a VM, through the representor Q_counters for the VF which are now exposed over the host.
    • With this feature, a kernel error log is now generated when certain fatal QP errors occur.
    • Added support for the following operating systems:
      • RHEL 9.2
      • RHEL 8.8
      • SLES15-SP5
    ]]>         The following issues have been fixed in version 23.04-1.1.3.1:

    • Installing "mlnx_tune" on Python3 did not work properly. "mlnx_tune" now supports Python3 in addition to Python2.
    • Changing traffic class via the sysfs while modifying QPs in parallel caused a deadlock.
    • Due to a bug in the emulation layer, performance degradation was experienced when running GPUDirect over Virtual Functions.
    • "debugfs" directories could not be created for representors and sub-functions, thus the log showed error for both the scenarios.
    • "knem" did not fully support RHEL8.7 and newer releases.
    ]]>         No new features or changes have been included in version 5.8.

    ]]>         The following issues have been fixed in version 5.8:

    • The redundant freeing of a list item could lead to memory corruption, potentially causing the application to crash or incorrect traffic handling.
    • The host driver probe did not check whether there are existing SFs which are present in the device, causing the host driver to not recreate those SFs.
    • The kernel went into panic mode if there were multiple encapsulations and not all neighbors were valid.
    ]]>
  • Fixed an issue of sending a command to physical devices during device discovery.
  • Fixed an issue where the OS crashes when a drive is hot removed during I/O stress test.
  • Fixed an issue where the OS crashes on aarch64 servers using the out-of-box driver during driver initialization.
  • Added sysfs entry for NUMA node in /sys/block/sdX/device. NUMA node detail is added for each exposed device similar to NVMe devices.
    • ]]>         Initial Release

    ]]>         Introduced support for iLO 6.

    ]]>         - Fixed an issue where HPONCFG Windows smart component failing to upload to iLO repository when iLO is in CNSA state.

    ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Fix for V6 Read disturb issue (which might have caused data integrity issue) and other issues.
    • ]]>
  • Fix for V6 Read disturb issue (which might have caused data integrity issue) and other issues.
    • ]]>         This product now supports  ResetToDefault property(RDE Port Schema).

    ]]>         This product addresses an issue where InterfaceEnabled property is read only and it can't patch this property

    ]]>
  • This product now supports RDE Read and Write operations.
  • This product now supports Debug Dump feature.
  • This product now supports new parameters when software requesting on Port 0(via AQ the connectivity type)
    • ]]>
  • Added support for Remote Key Management of Managed SED.
  • Added the Authority Key Identification 'security show' command in the SSA CLI for SPDM.
    • ]]>
  • Fixed an issue in SSA CLI where failed drive details were shown twice in the show config output.
  • Fixed an issue in SSA CLI where an error message was not being generated while performing an invalid modify command.
  • Fixed an issue in SSA CLI where the tool would display a Reboot required reason when modifying MRRS value to same value.
  • Fixed an issue in SSA CLI that would display an invalid error string in the show foreignmasterkeyidentifier output with Managed SEDs.
  • Updated SSA CLI to not list drivetypes that do not have the correct number of drives to modify an array with Managed SEDs.
  • Fixed an issue in SSA Scripting where a volume creation would fail when Remote SED mode was enabled and waiting for reboot.
    • ]]>         Initial Release

    ]]>         Fix issues of MCTP over I2C fix for obtaining Endpoint ID(EID), and SPDM support fix onto MCTP reply message.

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This is the initial version of the firmware.

    Known Issues:

    None

    ]]>
  • This is a Firmware maintenance release of Samsung PM1743 NVMe SSD with HPK5
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.
  • The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.
  • Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.
    • ]]>
  • This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.
  • The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.
  • Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

    New features and changes included in version 20.38.1002:

    • Improved token calculation.
    • Added support for forwarding INT packets to the user application for monitoring purposes by matching the BTH acknowledge request bit (bth_a).
    ]]>         The following issues have been fixed in version 20.38.1002:

    • A link failure that occurred due to a wrong 'is_inphi_cable' indication.
    • Fixed a firmware assert that occurred when tried to verify if  the module supported  "swap".
    ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

     

    New features and changes included in version 20.37.1700:

    • A new capability enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Updated the link maintenance flow to avoid high uncorrectable error rate. 
    ]]>         No fixes in this version.

    ]]>         For Gen11 PR3 & 2023 March MSB

    ]]>         Support Gen11 Intel servers.

    ]]>         Introduced support for iLO6.

    ]]>         - Fixed an issue where HPONCFG package failing to upload to iLO repository when iLO is in CNSA state.

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This is the initial version of the firmware.

    Known Issues:

    None]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This is the initial version of the firmware.

    Known Issues:

    None

    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>         .

    The following fixes were incorporated in this version:

    • The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.

    • The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.

    • Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.

    • If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.

    Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

    ]]>
  • Added support for Remote Key Management of Managed SED.
    • ]]>
  • Updated SSA GUI to show foreign volume status as SED data are locked.
  • Updated SSA GUI to allow modifying the controller cache settings when foreign volumes are present with Managed SEDs.
    • ]]>         Initial Release

    ]]>
  • Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm.
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>         New release.

    ]]>
  • Update the component version to resolve host incompatibility with vLCM Image after updating with predefined baseline.
  • Fix OS upgrade failure due to unreplaced Gen9 AMS CLI component.
    • ]]>
  • Added support for improving secure erase time for disks supporting the WRITE SAME command.
  • Added support for Remote Key Management of Managed SED.
  • Added support to ensure Remote/Local Key Management of Managed SED can be sanitized.
  • Added support for re-enabling failed logical drive by rebuilding selected drives.
  • Added support for cascaded expander to uniquely identify the attached enclosure and physical devices.
  • Added support for a redundant copy of controller settings data.
  • Introduce an HII option labeled 'Configure Controller UEFI Driver Health Reporting' within the 'Configure Controller Settings' menu to provide the capability to enable or disable the reporting of configuration errors and driver health.
  • Introduce an HII option labeled 'Controller Password State' within the CBE (Controller-Based Encryption) settings, enabling the actions to unset, temporarily suspend, and resume the controller password.
  • Updated the Redfish resource to align with the DMTF 2022.2 schema bundle, including the incorporation of Redfish annotations.
  • Adjusted the severity for Redfish Volume Status.Health state and DriveOffline alert for Foreign SED.
  • Create Redfish Volumes with a RAIDType set to 'None' for HBA (Host Bus Adapter) drives.
    • ]]>
  • Fixed issues related to spare drive functionality.
  • Fixed issues pertaining to Self-Encrypting Drive (SED) functionality.
  • Fixed an issue where SATA commands became unresponsive or stuck.
  • Fixed an issue where Redfish events of battery and WriteCache do not meet requirements.
  • Fixed an issue where firmware incorrectly reported unrecoverable media errors.
  • Fixed an issue where the surface scan progress status is displayed as "In progress" even after disabling the surface scan on the controller.
  • Fixed an issue related to the failure of the clear controller configuration command.
  • Fixed an issue of power surge when too many SATA drives are spinning up simultaneously.
  • Fixed an issue where MCTP over PCIe VDM is disabled while disabling VDM notification.
  • Fixed an issue where PLDM event consumer was missing events from the previous boot.
  • Fixed an issue where the completion date of the consistency check was incorrectly recorded.
  • Fixed an issue where firmware was processing additional unlock adapter password request even if the controller was already unlocked.
  • Fixed issues where logical drives were lost after a controller reset to factory defaults, especially when the 'preserve logical drive' option was enabled, and after an abrupt reboot where the controller reset to factory defaults, causing RAID loss.
  • Fixed migrating a SmartCache when destination controller has existing logical drive.
  • Fixed inaccuracies in SES enclosure behavior during hot-adding and hot-removing procedures.
  • Fixed issues where logical drives were lost after a controller reset to factory defaults, especially when the 'preserve logical drive' option was enabled, and after an abrupt reboot where the controller reset to factory defaults, causing RAID loss.
  • Fixed a controller lock-up problem triggered by a Loss of Sync (LOS) during sequential write traffic.
  • Fixed an issue causing system freezes during boot after enabling Secured-Core (DMAr) in RBSU.
  • Fixed an issue where the BatteryMissing event was not being sent when the battery was removed prior to boot.
  • Fixed an issue where a DriveOffline Redfish alert is not sent when a Drive resource initiated a sanitize operation.
  • Fixed an issue where the controller's attempt to update an unflashable UBM resulted in an error report.
  • Fixed an issue where an unflashable SMP PSOC (System Management Processor Programmable System-on-Chip) device was incorrectly appearing in the Type 5 downstream devices.
  • Enable Self-Encrypting Drive (SED) RKM (Recovery Key Management) support in the UEFI configuration.
  • Fixed an issue where driver health error messages were not displayed when the system language was changed to a non-English language.
  • Fixed an issue of incorrectly reporting the WriteCachePolicy for a Volume resource as "ProtectedWriteBack" when the cache was temporarily disabled.
  • Correct Redfish properties when backup power source is removed.
  • Fixed an issue where the controller failed to report storage information in the absence of physical drives.
  • Fixed an issue where an unexpected 'BatteryCharging' event was reported when no battery was present.
    • ]]>         Initial Release

    ]]>
  • Improve the FW about data mismatch after SPL
    • ]]>
  • Improve the FW about data mismatch after SPL
    • ]]>
  • Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm.
    • ]]>         New features and changes included in version 22.37.1700:

    • Added a safety mechanism to prevent the link from to getting stuck when receiving bad tuning results. In this case, the linkup flow is restarted and the mechanism retries to raise the link.
    • Improved rate limit token re-distribution algorithm.
    • Improved non-consumed bandwidth re-distribution.
    • Added mergeable buffer support (VIRTIO_NET_F_MRG_RXBUF in virtio spec) for VDPA kernel mode to improve performance in case of large MTU such as 9K. The feature is disabled by default and must be manually enabled while creating or modifying the virtio device.

        Note: For best performance, it is NOT recommended to enable the feature if the VDPA MTU is set to the default value (1500).

    • A new capability that enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Added a flow rule that enables offloading of multicast traffic by broadcasting it to multi-Flow-Table in FDB.
    • Enables a smooth and statically switch between PCC algorithms. In addition, the user can now switch between PCC algorithms while running traffic.
    • Added support for running PCC firmware trace without saving and sending the DB strings to the tool with the following changes:
      • Added new string section to the user PCC image creation tool
      • Added the new PCC DB strings to MTRC access registers output
      • On the tool's part: added support to reading the string.db using the MTRC access registers
    • Added support for 32 actions in the header modify pattern using bulk allocation.
    • The software can explicitly set the SL of an RTT response packet, instead of it being taken from the RTT request packet's SL. The RTT response packet SL may be set/queried via the CONGESTION_CONTROL_HCA_NP_PARAMETER MAD.
       
    ]]>         The following issues have been fixed in version 22.37.1700:

    • No ping in NODNIC VF when VLAN stripping was enabled.
    • vDPA application initialization failed due to virtual queue creation failure. The failure came with the "0x8f7a: ring address translate failed" assert which indicates incorrect permission supplied by QEMU for virtual ring memory.
    • CNP received, handled, and ignored counters in the hardware counters could not work after moving to Programmable Congestion Control mode.
    ]]>         New features and changes included in version 22.35.1012:

    • Improved both TP1a compliance and Physical-layer performance. TX and PLL settings were changed to comply with IEEE 802.3bs TP1a and improved link margins. 
    • Enabled the firmware to distribute loopback QPs/SQs between all LAG ports during the initial distribution in steering LAG.
    • Changed the Tx setting for optics HDR to improve compliance margins.
    • HPCC related configurations are now supported via the mlxconfig utility.
    • Added support for copy modify header steering action to/from the UDP field.
    • Added support for range based lookup. This new capability is available using the following new PRM command:

    GENERATE WQE which receives GTA WQE, the command supports "match on range" and num_hash_definer=[1,2] and num_match_ste=[1,2].
    For further information, refer to section "RTC Object Format" in the PRM.

    • Added support for RoCE based VM migration.
    • Added the following resource dump segments:

    SEG_HW_STE_FULL that includes dump to STE and all its dependencies
    SEG_FW_STE_FULL that include dump to FW_STE and to HW_STE_FULL in range

    • As the software requires additional space before and after a packet is scattered for its processing for stridden RQ, the hardware will allocate the required room while scattering packets to spare a copy. 
    • Improved security offload's Connections per Second (CPS) rate using the general object DEK (PSP TLS etc).
    • Added support for pre-copy commands in VF migration flow in order to reduce the migration downtime.
    • Optimized performance to support full VF migration flow.
    • Increased the VirtIO hardware offload message rate to 20/20 MPPS for 256 virtual devices by optimizing the datapath application code.
    • Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.
    • QoS priority trust default state can now be changed using the new nvconfig below:

    QOS_TRUST_STATE_P1
    QOS_TRUST_STATE_P2
    The values that can be used to set the default state are:
    TRUST_PORT
    TRUST_PCP
    TRUST_DSCP
    TRUST_DSCP_PCP

    ]]>         The following issues have been fixed in version 22.35.1012:

    • RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
    • Commands sent by the MLNX_OFED driver to the NIC would fail when loading the VirtIO driver. 
    • A firmware limitation caused enabling tx_port_ts to result in syndrome 0x5d2974.
    • PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
    • PCIe SKP OS generation interval for Gen1 and Gen2.
    • CPU handling synchronization required separation (run ptp4l with taskset -c [cpu #] prefix) while running heavy traffic. 
       
    ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>         New release.

    ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>
  • DMTF PLDM Redfish Device Enablement enhancements
    • Support Volume Creation and Deletion by the following Redfish requests
      • POST VolumeCollection
      • DELETE Volume
      • GET Volume Capabilities
    • Added support for the following Redfish ACTION requests:
      • POST Storage.ResetToDefaults
      • POST Volume.Initialize
      • POST Drive.SecureErase
    • Added support for Redfish PATCH requests for the following properties:
      • PATCH Volume.DedicatedSpareDrives
      • PATCH Volume.DisplayName
      • PATCH Volume.ReadCachePolicy
      • PATCH Volume.WriteCachePolicy
      • PATCH Drive.HotspareType
      • PATCH Drive.LocationIndicatorActive
      • PATCH Drive.WriteCacheEnabled
  • Support DMTF PLDM firmware update for drive
    • ]]>
  • Fix a00127934en_us: HPE ProLiant Gen10 Plus Servers - Unable to Switch From LKM to EKM With MR Controllers When Boot Time Password is Set
  • Fix an issue that Sanitize Block Erase on NVMe drive along with shutdown sequence may cause assertion in firmware.
  • Fix an issue that GET Volume query from REST client may fail when multiple Volumes are configured on the controller
  • Fix an issue that firmware throws error when setting WCE (Disk Write Cache) = 0 for JBOD drive.
  • Fix an issue that HDD sensor shows temperature on 14-HD Max when there is no drive installed.
  • Fix an issue that HII page may hang while there is pinned cache then do drives initialization and View Server Profile.
  • Fix a rare issue that controller may not getting discovered when there is power loss during cache restoration from a previous power loss.
  • Fix an issue that controller may hang and Online Controller Reset is triggered after running "storcli /cx set debug reset all" and then "storcli /cx get snapdump".
  • Fix an issue that enable security on logical drive may enable security on other unrelated drives which were configured as Dedicated Spare drive for other secured logical drive before.
  • Fix an issue that drive running sanitize overwrite may become Unconfigured Bad Unsupported after a cold boot
  • Fix a rare issue that firmware may hit assertion failure when a drive causes IO issue and fails.
  • Fix an issue that IML 1906 may be incorrectly logged when doing config clear and reboot.
  • Fix an issue that NVMe drives may move to Unconfigured Bad state from Unconfigured Good during driver unload-reload.
  • Fix an issue that SPDM GET_MEASUREMENTS command signature verification is failing at iLO
    • ]]>         This Firmware package contains following firmware versions:

    Adapter

    Speed

    MBI

    Firmware

    UEFI

    Boot Bios
    HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter 32Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter 32Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter 64Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter 64Gb 02.08.05 09.12.01 7.34 0.0

    Non-disruptive firmware upgrades: non-disruptive firmware updates is enabled and will not require a server reboot to apply.

    ]]>         Fixed the following behavior:

    Temperature Misreading: the adapter was reading incorrect reading of the temperature on the HPE SN1610Q 32Gb Fibre Channel Host Bus adapter's Small Form-factor Pluggable. The symptom would result in a temperature spike and potentially reset the system

    ]]>         This Firmware package contains following firmware versions:

    Adapter

    Speed

    MBI

    Firmware

    UEFI

    Boot Bios
    HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter 32Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter 32Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter 64Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter 64Gb 02.07.06 09.09.20 7.28 0.0
    ]]>         The Firmware fixes the following:

    • Unsuccessful read of the SFP Temperature which will trigger a Server Shutdown. 
    • Message related to a Mailbox 0x48 Firmware dump saved to buffer.
    ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         Updated to driver version 14.2.589.10-1

    ]]>
  • Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm.
    • ]]>
  • Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm.
    • ]]>         Updated to version 3.3-3

    ]]>         Updated to version 3.3-3

    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         This product fix an issue that TCP traffic on VMs might be interrupted if PF undergoes a reset.

    ]]>         The following changes and new features have been included in version 23.04-1.1.3.1

    • Starting this release, MLNX EN+RoCE drivers will adopt the following versioning naming scheme: YY.MM-x.x.x.x (i.e., Year.Month-x.x.x.x).
    • Added support for allowing the host to track various statistics for the VFs, specifically all of the Q_counters stats even if he gives the VF to a VM, through the representor Q_counters for the VF which are now exposed over the host.
    • With this feature, a kernel error log is now generated when certain fatal QP errors occur.
    • Added support for the following operating systems:
      • RHEL 9.2
      • RHEL 8.8
      • SLES15-SP5
    ]]>         The following issues have been fixed in version 23.04-1.1.3.1:

    • Installing "mlnx_tune" on Python3 did not work properly. "mlnx_tune" now supports Python3 in addition to Python2.
    • Changing traffic class via the sysfs while modifying QPs in parallel caused a deadlock.
    • Due to a bug in the emulation layer, performance degradation was experienced when running GPUDirect over Virtual Functions.
    • "debugfs" directories could not be created for representors and sub-functions, thus the log showed error for both the scenarios.
    • "knem" did not fully support RHEL8.7 and newer releases.
    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>         .

    .

    The following fixes were incorporated in this version:

    • The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.

    • The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.

    • Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.

    • If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.

    Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

    ]]>
  • Added support for RHEL 9.
    • ]]>
  • Firmware addresses a hot plug reporting concern
    • ]]>         This product now supports HPE ProLiant Gen11 Platforms with Intel processors

    ]]>         This product now supports Gen11 platfroms.

    ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>         New release.

    ]]>         The following fixes were incorporated in this version:

    • Code optimization to save memory repo.

    • TLB exception seen while doing esp reset when expander reset was in progress.

    • Added the psoc 8.93 binary in peripheral images, updated the reveille version numbers.

    • Added whole new Delta PS-pmbus code , Updated the ESP version number.

    Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

    ]]>
  • Firmware addresses a hot plug reporting concern
    • ]]>         TBD

    ]]>         This product enhanced the compatibility with new kernel supported.

    ]]>
  • Driver update
    • ]]>
  • Added support for AHCI controller device
    • ]]>
  • Added support for vSphere 8.0U2.
    • ]]>
  • Added support for vSphere 8.0
    • ]]>
  • Fixed issue where ilo driver is failing to acquire contiguous physical memory below 4GB causing userworld apps like hponcfg to be unable to communicate with iLO.
    • ]]>
  • Addresses a hot plug reporting concern
  • Increased the buffer memory size used for sequential write data to resolve performance degradation seen in a RAID60 configuration
    • ]]>
  • Addresses a hot plug reporting concern
  • Increased the buffer memory size used for sequential write data to resolve performance degradation seen in a RAID60 configuration
    • ]]>
  • Fixed an issue of sending a command to physical devices during device discovery.
  • Fixed an issue where the OS crashes when a drive is hot removed during I/O stress test.
  • Fixed an issue where the OS crashes on aarch64 servers using the out-of-box driver during driver initialization.
  • Added sysfs entry for NUMA node in /sys/block/sdX/device. NUMA node detail is added for each exposed device similar to NVMe devices.
    • ]]>         Initial Release

    ]]>
  • Added support for Qualcomm X100
  • Added enhanced support to iLO firmware to report additional description about the components for HPE GreenLake Compute Ops Management initiated firmware bundle update
  • Added support to enable or disable User Accounts through Redfish and iLO web interface
  • In-band IPMI support for HPE ProLiant RL300 Gen11 servers (RHEL 8.6)
  • For PLDM components, added support to selectively update the target devices on the system through Install Sets and Task Queue
    • ]]>
  • Fixed CloudConnect retry logic to reconnect to iLO once connectivity is resumed
  • Fixed the auto-connect issue if the HPE GreenLake Compute Ops Management (COM) was disabled due to a no-retry
    • ]]>
  • iLO needs to provide IPv4 address for RDE enabled NIC
  • NVIDIA L40S needs to be enabled on HPE Servers (Gen11, Gen10 Plus)
  • iLO enablement for Intel Ponte Vecchio (PVC) for accelerator manageability and supportability
  • Reduce EDSFF power consumption using NVMe Power States feature
  • iLO enhancements to support SMBIOS 3.86 spec (type 197 and 242)
    • ]]>
  • Increased the maximum boot order to 512 as specified by UEFI EV specification
  • Incorrect sensor values for some sub-components in IPMI response
  • The "Ignore" option for the "Global Component Integrity" security parameter in the iLO Security Dashboard gets automatically disabled
  • The discrepancy between M.2 Slot Name with Redfish URI and iLO GUI is removed. The product name getting from backend will be displayed in redfish and UI as well
  • Enforced a limit of 14 bytes for DHCP v4 clientId. An error response of "400 - Bad Request" will be observed if the length is beyond 14 characters
  • Removal of duplicate sensor entries from IPMI response
  • UefiDevicePath length increased from 256 bytes to 1024 bytes
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         The following changes and new features have been included in version 23.04-1.1.3.1

    • Starting this release, MLNX EN+RoCE drivers will adopt the following versioning naming scheme: YY.MM-x.x.x.x (i.e., Year.Month-x.x.x.x).
    • Added support for allowing the host to track various statistics for the VFs, specifically all of the Q_counters stats even if he gives the VF to a VM, through the representor Q_counters for the VF which are now exposed over the host.
    • With this feature, a kernel error log is now generated when certain fatal QP errors occur.
    • Added support for the following operating systems:
      • RHEL 9.2
      • RHEL 8.8
      • SLES15-SP5
    ]]>         The following issues have been fixed in version 23.04-1.1.3.1:

    • Installing "mlnx_tune" on Python3 did not work properly. "mlnx_tune" now supports Python3 in addition to Python2.
    • Changing traffic class via the sysfs while modifying QPs in parallel caused a deadlock.
    • Due to a bug in the emulation layer, performance degradation was experienced when running GPUDirect over Virtual Functions.
    • "debugfs" directories could not be created for representors and sub-functions, thus the log showed error for both the scenarios.
    • "knem" did not fully support RHEL8.7 and newer releases.
    ]]>         No new features or changes have been included in version 5.8.

    ]]>         The following issue has been fixed in version 5.8(A):

    • On Red Hat Enterprise Linux 8 Update 7 (x86_64) errata kernel version 4.18.0-425.10.1 and later the HPE Mellanox RoCE (RDMA over Converged Ethernet) Driver 5.8 fails to load correctly because of symbol mismatch in the kernel modules and weak-updates failure. The version 5.8(A) is built against the errata kernel version 4.18.0-425.10.1 and fixes the above issue on this and the later Red Hat Enterprise Linux 8 Update 7 errata kernel versions.

    The following issues have been fixed in version 5.8:

    • The redundant freeing of a list item could lead to memory corruption, potentially causing the application to crash or incorrect traffic handling.
    • The host driver probe did not check whether there are existing SFs which are present in the device, causing the host driver to not recreate those SFs.
    • The kernel went into panic mode if there were multiple encapsulations and not all neighbors were valid.
    ]]>         This Firmware package contains following firmware versions:

    Adapter

    Speed

    Universal Boot Image

    Firmware

    UEFI

    Boot Bios

    HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter

    32Gb

    14.2.589.5

    14.2.589.5

    14.2.579.0

    14.2.566.0

    HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter

    32Gb

    14.2.589.5

    14.2.589.5

    14.2.579.0

    14.2.566.0
    HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter 64Gb 14.2.589.5 14.2.589.5 14.2.579.0 14.2.566.0
    HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter 64Gb 14.2.589.5 14.2.589.5 14.2.579.0 14.2.566.0
    ]]>         This Firmware package contains following firmware versions:

    Adapter

    Speed

    Universal Boot Image

    Firmware

    UEFI

    Boot Bios

    HPE SN1610E 32Gb Single Port Fibre Channel Host Bus Adapter

    32Gb

    14.0.499.29

     14.0.499.29

    14.0.499.2

    14.0.490.0

    HPE SN1610E 32Gb Dual Port Fibre Channel Host Bus Adapter

    32Gb

    14.0.499.29

     14.0.499.29

    14.0.499.2

    14.0.490.0
    HPE SN1700E 64Gb Single Port Fibre Channel Host Bus Adapter 64Gb 14.0.499.29  14.0.499.29 14.0.499.2 14.0.490.0
    HPE SN1700E 64Gb Dual Port Fibre Channel Host Bus Adapter 64Gb 14.0.499.29  14.0.499.29 14.0.499.2 14.0.490.0
    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         This product enhanced the compatibility with new drivers

    ]]>         TBD

    ]]>         Driver version 5.3.81.2_1

    This Driver is supported on VMware 7.0U3 only 

    ]]>         Driver version 5.3.1.0

    This Driver is supported on VMware 7.0U3 only 

    ]]>         This product addresses an issue where Loses IP Address Randomly during AC/DC cycle and idling.

    ]]>         This product addresses an issue where the FAN behavior with installed BCM 5719 1Gb 4p BASE-T OCP Adptr.

    ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         This package supports only SuSE Linux Enterprise Server(SLES) Distros

    ]]>         This package supports only SuSE Linux Enterprise Server(SLES) Distros

    ]]>
  • This product now changes default number of queues for high core count platforms
  • This product changes the default setting where the GNSS(GNSS_SUPPORT) is disabled now
    • ]]>
  • This product fixes an issue where the virtual function failed to create
  • This product fixes an issue where crash is observed when changing the bonding mode from Balance TLB to 802.3ad
  • This product fixes an issue where the traffic goes to unintended random rx_queues when number of parallel stream increased in iperf even if affinity is set
    • ]]>         This product enhanced the availability of debugfs functionality when UEFI Secure Boot is enabled

    ]]>
  • This product fixes an issue where it has conflict with Mellanox or other network drivers. Please also update hpe-auxiliary RPM to v.1.0.3 for sles15sp3
  • This product correct an issue which the RPM metadata missing pci-id
    • ]]>
  • Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm.
    • ]]>
  • Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm.
    • ]]>         New features and changes included in version 26.37.1700:

    • Modified the RDE behavior to return an error if the chassis ID subtype is AgentId, or Port ID subtype is ChassisComp.
    • Enabled VF LAG hash mode. The LAG_RESOURCE_ALLOCATION mlxconfig field is now modifiable.
    • A new capability enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Added a flow rule that enables offloading of multicast traffic by broadcasting it to multi-Flow-Table in FDB.
    • Enables a smooth and statically switch between PCC algorithms. In addition, the user can now switch between PCC algorithms while running traffic.
    • Added support for 32 actions in the header modify pattern using bulk allocation.
    ]]>         The following issues have been fixed in version 26.37.1700:

    • An issue that prevented the adapter card from handling WoL packets when the host powered up directly into the standby mode.
    • CNP received, handled, and ignored counters in the hardware counters could not work after moving to Programmable Congestion Control mode.
    ]]>         New Features and Changes in Version 26.35.1012:

    • Added support for copy modify header steering action to/from the UDP field.
    • Added the following resource dump segments:

    SEG_HW_STE_FULL that includes dump to STE and all its dependencies
    SEG_FW_STE_FULL that include dump to FW_STE and to HW_STE_FULL in range

    • As the software requires additional space before and after a packet is scattered for its processing for stridden RQ, the hardware will allocate the required room while scattering packets to spare a copy. 
    • QoS priority trust default state can now be changed using the new nvconfig below:

    QOS_TRUST_STATE_P1
    QOS_TRUST_STATE_P2
    The values that can be used to set the default state are:
    TRUST_PORT
    TRUST_PCP
    TRUST_DSCP
    TRUST_DSCP_PCP

    ]]>         The following issues have been fixed in version 26.35.1012:

    • The patch to the RDE LLDPEnable property in Port schema would not be updated after the host reboot.
    • RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
    • PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
    • PCIe SKP OS generation interval for Gen1 and Gen2.
    ]]>         Updated to driver version 14.2.589.10-1

    ]]>         Updated to driver version 14.0.499.31

    ]]>         Added support for:

    Red Hat Linux 8.8

    Red Hat Linux 9.2

    SLES 15 SP5

    Updated Driver version 10.02.10.00-k1

    ]]>         updated to the version: 10.02.07.01_k1-2

    ]]>
  • Improve the FW about data mismatch after SPL issued.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>
  • DMTF PLDM Redfish Device Enablement enhancements
    • Support Volume Creation and Deletion by the following Redfish requests
      • POST VolumeCollection
      • DELETE Volume
      • GET Volume Capabilities
    • Added support for the following Redfish ACTION requests:
      • POST Storage.ResetToDefaults
      • POST Volume.Initialize
      • POST Drive.SecureErase
    • Added support for Redfish PATCH requests for the following properties:
      • PATCH Volume.DedicatedSpareDrives
      • PATCH Volume.DisplayName
      • PATCH Volume.ReadCachePolicy
      • PATCH Volume.WriteCachePolicy
      • PATCH Drive.HotspareType
      • PATCH Drive.LocationIndicatorActive
      • PATCH Drive.WriteCacheEnabled
  • Support DMTF PLDM firmware update for drive
    • ]]>
  • Fix a00127934en_us: HPE ProLiant Gen10 Plus Servers - Unable to Switch From LKM to EKM With MR Controllers When Boot Time Password is Set
  • Fix an issue that Sanitize Block Erase on NVMe drive along with shutdown sequence may cause assertion in firmware.
  • Fix an issue that GET Volume query from REST client may fail when multiple Volumes are configured on the controller
  • Fix an issue that firmware throws error when setting WCE (Disk Write Cache) = 0 for JBOD drive.
  • Fix an issue that HDD sensor shows temperature on 14-HD Max when there is no drive installed.
  • Fix an issue that HII page may hang while there is pinned cache then do drives initialization and View Server Profile.
  • Fix a rare issue that controller may not getting discovered when there is power loss during cache restoration from a previous power loss.
  • Fix an issue that controller may hang and Online Controller Reset is triggered after running "storcli /cx set debug reset all" and then "storcli /cx get snapdump".
  • Fix an issue that enable security on logical drive may enable security on other unrelated drives which were configured as Dedicated Spare drive for other secured logical drive before.
  • Fix an issue that drive running sanitize overwrite may become Unconfigured Bad Unsupported after a cold boot
  • Fix a rare issue that firmware may hit assertion failure when a drive causes IO issue and fails.
  • Fix an issue that IML 1906 may be incorrectly logged when doing config clear and reboot.
  • Fix an issue that NVMe drives may move to Unconfigured Bad state from Unconfigured Good during driver unload-reload.
  • Fix an issue that SPDM GET_MEASUREMENTS command signature verification is failing at iLO
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>         Added support for:

    Red Hat Linux 8.8

    Red Hat Linux 9.2

    SLES 15 SP5

    Updated Driver version 10.02.10.00-k1

    ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.
    • ]]>
  • Firmware addresses a hot plug reporting concern
    • ]]>         For Gen11 PR3 & 2023 March MSB

    ]]>         For Gen11 PR1 usage.

    ]]>
  • Added support for Microsoft Windows Sever 2022.
    • ]]>
  • Fix command timeout and uncorrectable error improvement.
  • Added features for SAS4 auto power swtiching and thermal requirement.
    • ]]>
  • This firmware version fixes a bug with the unmap command that may cause a drive hang
    • ]]>
  • Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm.
    • ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         This product now supports RHEL 8.7

    ]]>         This product fixes an issue where the firmware update failed when secure boot is enabled

    ]]>         This product fix an issue where it has warning message during compilation

    ]]>
  • Added support for Remote Key Management of Managed SED.
    • ]]>
  • Updated SSA GUI to show foreign volume status as SED data are locked.
  • Updated SSA GUI to allow modifying the controller cache settings when foreign volumes are present with Managed SEDs.
    • ]]>         Initial Release

    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for Gen10/Gen10 Plus platforms
    • ]]>         Initial release.

    ]]>         This product enhanced the compatibility with firmware of CVL4.2.

    ]]>
  • This product enhanced the compatibility with firmware of CVL4.1.
  • This product now supports the following new server.

    • HPE ProLiant DL560 Gen11 Server
    HPE ProLiant DL110 Gen11 Server
    HPE ProLiant ML110 Gen11 Server

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>         This Firmware package contains following firmware versions:

    Adapter

    Speed

    MBI

    Firmware

    UEFI

    Boot Bios
    HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter 32Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter 32Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter 64Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter 64Gb 02.08.05 09.12.01 7.34 0.0

    Non-disruptive firmware upgrades: non-disruptive firmware updates is enabled and will not require a server reboot to apply.

    Added support for:

    Red Hat Linux 8.8

    Red Hat Linux 9.2

    SLES 15 SP5

    ]]>         Fixed the following behavior:

    Temperature Misreading: the adapter was reading incorrect reading of the temperature on the HPE SN1610Q 32Gb Fibre Channel Host Bus adapter's Small Form-factor Pluggable. The symptom would result in a temperature spike and potentially reset the system

    ]]>         This Firmware package contains following firmware versions:

    Adapter

    Speed

    MBI

    Firmware

    UEFI

    Boot Bios
    HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter 32Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter 32Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter 64Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter 64Gb 02.07.06 09.09.20 7.28 0.0
    ]]>         The Firmware fixes the following:

    • Unsuccessful read of the SFP Temperature which will trigger a Server Shutdown. 
    • Message related to a Mailbox 0x48 Firmware dump saved to buffer.
    ]]>
  • Fix for potential hangs and timeouts, tuning fixes based on field experience and maintenance logging items
    • ]]>
  • Fix for potential hangs and timeouts, tuning fixes based on field experience and maintenance logging items
    • ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

    New features and changes included in version 20.38.1002:

    • Improved token calculation.
    • Added support for forwarding INT packets to the user application for monitoring purposes by matching the BTH acknowledge request bit (bth_a).
    ]]>         The following issues have been fixed in version 20.38.1002:

    • A link failure that occurred due to a wrong 'is_inphi_cable' indication.
    • Fixed a firmware assert that occurred when tried to verify if  the module supported  "swap".
    ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

     

    New features and changes included in version 20.37.1700:

    • A new capability enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Updated the link maintenance flow to avoid high uncorrectable error rate. 
    ]]>         No fixes in this version.

    ]]>
  • Updated supported platforms
    • ]]>
  • Added support for Intel platforms
    • ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>
  • ​​Firmware adds support for new humidity sensor
    • ]]>         Updated to Driver version 14.2.567.0

    ]]>         Updated to Driver version 14.0.543.0

    ]]>
  • Added support for Remote Key Management of Managed SED.
  • Added the Authority Key Identification 'security show' command in the SSA CLI for SPDM.
    • ]]>
  • Fixed an issue in SSA CLI where failed drive details were shown twice in the show config output.
  • Fixed an issue in SSA CLI where an error message was not being generated while performing an invalid modify command.
  • Fixed an issue in SSA CLI where the tool would display a Reboot required reason when modifying MRRS value to same value.
  • Fixed an issue in SSA CLI that would display an invalid error string in the show foreignmasterkeyidentifier output with Managed SEDs.
  • Updated SSA CLI to not list drivetypes that do not have the correct number of drives to modify an array with Managed SEDs.
  • Fixed an issue in SSA Scripting where a volume creation would fail when Remote SED mode was enabled and waiting for reboot.
    • ]]>         Initial Release

    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Driver updates
    • ]]>
  • Added support for AHCI controller device
    • ]]>
  • Added support for RHEL 9
    • ]]>
  • Fixes an intermittent issue where the incorrect model number can be reported during spin-up
    • ]]>
  • Fixes an issue in previou version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on
    • ]]>         Firmware addresses a hot plug reporting concern

    ]]>
  • Addresses a hot plug reporting concern
  • Increased the buffer memory size used for sequential write data to resolve performance degradation seen in a RAID60 configuration
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Fix for V6 Read disturb issue (which might have caused data integrity issue) and other issues.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>         New release.

    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         TBD

    ]]>         This product enhanced the compatibility with new kernel supported.

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Problems Fixed:

    Addressed an issue where the MegaRAID controller status is displayed as "unknown" on the iLO web page.

    Known Issues:

    None]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Fix bugs found in the previous version and improve on TTR (Time To Ready) requirement to fix device temporarily not found issue after hot-plug.
    • ]]>

  • This component provides support only for VMD enabled Intel VROC platform.

    • ]]>
  • ​Added Relaxed Ordering feature in drive FW and fixed some bugs
    • ]]>         TBD

    ]]>
  • Initial version
  • This product enhances the way ENS RSS support (receive side scaling) is added, enhancing performance.
  • This product enhances the way LRO (Large Receive Offload) support is enabled and disabled, improving network efficiency.
  • This product adds to supports Vmware ESXi 8.0
  • This product adds to support HPE MicroServer Gen11
    • ]]>
  • This product fixes an issue where BFD controls were getting dropped (Bidirectional Forwarding Detection (BFD) protocol), ensuring network reliability.
  • This product fixes a problem where the ENS stack was invoking driver APIs with spinlock, improving system stability.
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Fixes an intermittent issue where the incorrect model number can be reported during spin-up.
    • ]]>         Fixed the following items: 

    • TBD
    ]]>         The following enhancements are available in this release:

      •  
    • Extend cpqSePciSlotEntry, cpqSePciFunctEntry, cpaSePCleDiskEntry OIDs index for supporting PCI multi-segment function.
    • Support NIC redundancy bonding function
    ]]>         Fixed the following items: 

    •  cpqSePCIeDiskOsName is now correctly displayed
    • Removed trailing spaces in the value of cpqSePCIeDiskModel, cpqNicIfPhysAdapterPartNumber, cpqSePciSlotBoardName, cpqSePCIeDiskFwRe
    ]]>
  • Fixes a false indication of rare capacitor test failure
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.
    • ]]>
  • Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.
    • ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>         New release.

    ]]>
  • Added support for Remote Key Management of Managed SED.
  • Added the Authority Key Identification 'security show' command in the SSA CLI for SPDM.
    • ]]>
  • Fixed an issue in SSA CLI where failed drive details were shown twice in the show config output.
  • Fixed an issue in SSA CLI where an error message was not being generated while performing an invalid modify command.
  • Fixed an issue in SSA CLI where the tool would display a Reboot required reason when modifying MRRS value to same value.
  • Fixed an issue in SSA CLI that would display an invalid error string in the show foreignmasterkeyidentifier output with Managed SEDs.
  • Updated SSA CLI to not list drivetypes that do not have the correct number of drives to modify an array with Managed SEDs.
  • Fixed an issue in SSA Scripting where a volume creation would fail when Remote SED mode was enabled and waiting for reboot.
    • ]]>         Initial Release

    ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This is the initial verison of the firmware.

    Known Issues:

    None

    ]]>         See the iSUT Release Notes for information about the enhancements added in this release

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         See the iSUT Release Notes for information about the enhancements added in this release

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         TBD

    ]]>         This product addresses an issue where update of Driver Copyright information

    ]]>
  • This product now add message when set VF's MAC Address
  • This product now supports RHEL 8.7
    • ]]>         This product fixes an issue where the resource is busy on RHEL8.6 VM when changing MTU

    ]]>
  • This product enhanced the wating time to wait MTU change.
  • This product enhanced ability to turn off CRC stripping for VF
    • ]]>
  • This product fixes an issue where it has race condition between iavf_open and iavf_handle_hw_reset
  • This product fixes an crash issue in iavf_suspend
  • This product fixes VF stuck in reset.
    • ]]>
  • Reverted OCP spec features to maintain compliance to OCP spec commands over NVMe-MI
  • Implemented real Active Measured Latency by adding OCP 2.0 C3 Log page
    • ]]>
  • Reverted OCP spec features to maintain compliance to OCP spec commands over NVMe-MI
  • Implemented real Active Measured Latency by adding OCP 2.0 C3 Log page
    • ]]>         Added support for:

    Red Hat Linux 8.8

    Red Hat Linux 9.2

    SLES 15 SP5

    Updated Driver version 10.02.10.00-k1

    ]]>         Updated to driver version 10.02.07.01-k1

    ]]>         Updated to driver version 14.2.589.10-1

    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         This product now supports  ResetToDefault property(RDE Port Schema).

    ]]>         This product addresses an issue where InterfaceEnabled property is read only and it can't patch this property

    ]]>
  • This product now supports RDE Read and Write operations.
  • This product now supports Debug Dump feature.
  • This product now supports new parameters when software requesting on Port 0(via AQ the connectivity type)
    • ]]>
  • Improves data integrity
  • Decreases possibility of data corruption in certain error and timing conditions
  • Reduces the probability of hangs
    • ]]>
  • Improves data integrity
  • Decreases possibility of data corruption in certain error and timing conditions
  • Reduces the probability of hangs
    • ]]>
  • Improve the FW about data mismatch after SPL issued.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         This package supports only Red Hat Enterprise Linux (RHEL) Distros

    ]]>         This package supports only Red Hat Enterprise Linux (RHEL) Distros

    ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Fixes an issue in previous version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on
    • ]]>
  • Fixes an issue in previous version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on
    • ]]>         This product now supports RHEL 9.1

    ]]>         This product fixes an issue where the firmware update failed when secure boot is enabled

    ]]>         This product fix an issue where it has warning message during compilation

    ]]>         .

    The following fixes were incorporated in this version:

    • The Enabled-ClusterS2D command now completes successfully when executed on a SATA drive within a D3610 disk enclosure for a NonStop solution.

    • The smart carrier, which is the drive case for SAS drives, now authenticates in the D3610/D3710 drive enclosure.

    • Added new 7-segment error codes E0 and E1 to report issues with Fan modules A and B, respectively. These new codes only apply to the D3610/D3710 and only display when running firmware 5.04.

    • If the storage enclosure processor within the I/O module fails, a hard reset (power down and then power up) is executed to ensure the processor comes back online.

    Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

    ]]>         Added support for:

    Red Hat Linux 8.8

    Red Hat Linux 9.2

    SLES 15 SP5

    Updated Driver version 10.02.10.00-k1

    ]]>         Updated to driver version 10.02.08.01_k1-1

    ]]>         Updated to version 1.0.0.1

    ]]>         Updated to version 1.0.0.1

    ]]>
  • Fixes an issue in previou version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on
    • ]]>
  • Firmware addresses a hot plug reporting concern.
    • ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         Updated to driver version 14.2.537.0

    The raw driver files can be obtained by extracting the Smart Component and then extracting the Emulex installer.  Use this command:

        elxdrvr-fc-version.exe /q2 extract=2

    The extracted files are located:

        C:\Users\Administrator\Documents\Emulex\Drivers\FC-version

    Each kit folder has subsequent architecture folders with subsequent OS folders.  For example,

        C:\Users\Administrator\Documents\Emulex\Drivers\FC-version\x64\win2019

    ]]>         Updated to driver version 14.0.534.0

    The raw driver files can be obtained by extracting the Smart Component and then extracting the Emulex installer.  Use this command:

        elxdrvr-fc-version.exe /q2 extract=2

    The extracted files are located:

        C:\Users\Administrator\Documents\Emulex\Drivers\FC-version

    Each kit folder has subsequent architecture folders with subsequent OS folders.  For example,

        C:\Users\Administrator\Documents\Emulex\Drivers\FC-version\x64\win2019

    ]]>         This product now supports  ResetToDefault property(RDE Port Schema).

    ]]>         This product addresses an issue where InterfaceEnabled property is read only and it can't patch this property

    ]]>
  • This product now supports RDE Read and Write operations.
  • This product now supports Debug Dump feature.
  • This product now supports new parameters when software requesting on Port 0(via AQ the connectivity type)
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Fix for potential hangs and timeouts, tuning fixes based on field experience and maintenance logging items
    • ]]>
  • Added support for RHEL 9.
    • ]]>         Updated to version 1.0.0.1

    ]]>         Updated to version 1.0.0.1

    ]]>
  • Added support for Qualcomm X100
  • Added enhanced support to iLO firmware to report additional description about the components for HPE GreenLake Compute Ops Management initiated firmware bundle update
  • Added support to enable or disable User Accounts through Redfish and iLO web interface
  • In-band IPMI support for HPE ProLiant RL300 Gen11 servers (RHEL 8.6)
  • For PLDM components, added support to selectively update the target devices on the system through Install Sets and Task Queue
    • ]]>
  • Fixed CloudConnect retry logic to reconnect to iLO once connectivity is resumed
  • Fixed the auto-connect issue if the HPE GreenLake Compute Ops Management (COM) was disabled due to a no-retry
    • ]]>
  • iLO needs to provide IPv4 address for RDE enabled NIC
  • NVIDIA L40S needs to be enabled on HPE Servers (Gen11, Gen10 Plus)
  • iLO enablement for Intel Ponte Vecchio (PVC) for accelerator manageability and supportability
  • Reduce EDSFF power consumption using NVMe Power States feature
  • iLO enhancements to support SMBIOS 3.86 spec (type 197 and 242)
    • ]]>
  • Increased the maximum boot order to 512 as specified by UEFI EV specification
  • Incorrect sensor values for some sub-components in IPMI response
  • The "Ignore" option for the "Global Component Integrity" security parameter in the iLO Security Dashboard gets automatically disabled
  • The discrepancy between M.2 Slot Name with Redfish URI and iLO GUI is removed. The product name getting from backend will be displayed in redfish and UI as well
  • Enforced a limit of 14 bytes for DHCP v4 clientId. An error response of "400 - Bad Request" will be observed if the length is beyond 14 characters
  • Removal of duplicate sensor entries from IPMI response
  • UefiDevicePath length increased from 256 bytes to 1024 bytes
    • ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This is the initial version of the firmware.

    Known Issues:

    None

    ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>         New release.

    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Improves data integrity
  • Decreases possibility of data corruption in certain error and timing conditions
  • Reduces the probability of hangs and provide a minor performance improvement
    • ]]>
  • Improves data integrity
  • Decreases possibility of data corruption in certain error and timing conditions
  • Reduces the probability of hangs and provide a minor performance improvement
    • ]]>         TBD

    ]]>
  • This product enhanced optimize drvier around user data copy. 
  • This product enhanced driver warning messages are thrown when driver reload.
  • This product enhanced to support XDP multibuffer.
  • This product enhanced ethtool to support CMIS 4.0 and backwards compatibility apart from compat changes.
    • ]]>
  • This product addresses an issue where System crash on running ethtool self test in loop on multiple adapter ports
  • This product addresses an issue where MSIX collision between L2 and RoCE drivers.
  • This product addresses an issue where Devlink reload command failed.
  • This product correct an issue which unable to recover from FW crash triggered by bnxtnvm fwcli 'crash fw_assert'.
  • This product correct an issue which the call traces while unloading bnxt_en and bnxt_re driver
  • This product correct an issue which ethtool -S crash when firmware is unhealthy
  • This product correct an issue which rdev allocation '__flush_work' issue by doing initialization for kernel workqueue.
    • ]]>         Fixed the following items: 

    • TBD
    ]]>         The following enhancements are available in this release:

      •  
    • Extend cpqSePciSlotEntry, cpqSePciFunctEntry, cpaSePCleDiskEntry OIDs index for supporting PCI multi-segment function.
    • Support NIC redundancy bonding function
    ]]>         Fixed the following items: 

    •  cpqSePCIeDiskOsName is now correctly displayed
    • Removed trailing spaces in the value of cpqSePCIeDiskModel, cpqNicIfPhysAdapterPartNumber, cpqSePciSlotBoardName, cpqSePCIeDiskFwRe
    ]]>
  • Fix for potential hangs and timeouts, tuning fixes based on field experience and maintenance logging items
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>         TBD

    ]]>
  • This product fix an issue that caused the driver to crash if it the vPort ID greater than the maximum supported vPorts.
  • This product fix an issue which the command returned an error although the link was up in ""mlx5cmd -linkspeed"". This happened when link up time exceeded 5 seconds.
    • ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Fix the detection issue on wondermiddle after hot-plug
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>         This product now supports  ResetToDefault property(RDE Port Schema).

    ]]>         This product addresses an issue where InterfaceEnabled property is read only and it can't patch this property

    ]]>
  • This product now supports RDE Read and Write operations.
  • This product now supports Debug Dump feature.
  • This product now supports new parameters when software requesting on Port 0(via AQ the connectivity type)
    • ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>         New release.

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Problems Fixed:

    Addressed an issue where the MegaRAID controller status is displayed as "unknown" on the iLO web page.

    Known Issues:

    None

    ]]>         Set the value of the Snoop Response Hold Off for IOAT Stack setting to 7 when the vRAN Workload Profile has been selected. This aligns with Intels performance tuning recommendation.

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Problems Fixed:

    Address an issue with some 4th Generation Intel Xeon Processors that can result in an unexpected reset with a machine check error logged to the Integrated Management Log (IML).  This issue is not unique to HPE systems.  The following is Intel’s description of the issue:  "Under complex microarchitectural conditions, the processor may experience a Caching Home Agent Table of Requests (TOR) timeout machine check exception."  This version of the System ROM will update internal processor firmware during boot.  This internal processor firmware cannot be downgraded even if the System ROM is downgraded. Using processors with different version of internal firmware is not supported.

    Addressed an issue where the speed of Kioxia EDSFF drive might be downgraded from PCIe Generation 5 to Generation 4.

    Known Issues:

    None

    ]]>
  • Updated supported platforms
    • ]]>
  • Added support for Gen11 platforms
    • ]]>
  • Fixes an issue in previou version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>         Remove DL325/385 Gen10 Plus servers.

    ]]>
  • This product enhanced NDIS packet drop monitoring support for Windows Server vNext.
  • This product enhanced to Implement RoCE variable size WQE(Work Queue Element) support for RDMA.
    • ]]>
  • This product addressed the code initialization in NDSPI(Network Direct Service Provider Interface) to enhance retransmit capability.
  • This product addressed the data retrieval for better RDMA connection.
  • This product addressed the disablement support of CQ overflow detection.
    • ]]>
  • This product enhances to support information logging of DBQ (Database Qualifier) events.
  • This product enhances to address a new method of retrieving data from the correct PFs by using the correct index value.
  • This product enhances to use I/O Workitem EX to handle passive level callbacks instead of standard NDIS workitems.
  • This product removes the Packet Direct advanced control panel options.
  • This product adds to support HPE MicroServer Gen11
    • ]]>         This product fixes an issue where the VF RoCE would not function if the default VLAN is enabled on vSwitch for the VF

    ]]>         Fixed the following items: 

    • TBD
    ]]>         The following enhancements are available in this release:

      •  
    • Extend cpqSePciSlotEntry, cpqSePciFunctEntry, cpaSePCleDiskEntry OIDs index for supporting PCI multi-segment function.
    • Support NIC redundancy bonding function
    • Support cpqNic information on SLES XEN Virtual interfaces
    ]]>         Fixed the following items: 

    •  cpqSePCIeDiskOsName is now correctly displayed
    • Removed trailing spaces in the value of cpqSePCIeDiskModel, cpqNicIfPhysAdapterPartNumber, cpqSePciSlotBoardName, cpqSePCIeDiskFwRe
    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This is the initial version of the firmware.

    Known Issues:

    None

    ]]>         Updated to version 1.0.0.0-4

    ]]>         Updated to version 1.0.0.0-4

    ]]>         Updated to driver version 14.2.537.0

    The raw driver files can be obtained by extracting the Smart Component and then extracting the Emulex installer.  Use this command:

        elxdrvr-fc-version.exe /q2 extract=2

    The extracted files are located:

        C:\Users\Administrator\Documents\Emulex\Drivers\FC-version

    Each kit folder has subsequent architecture folders with subsequent OS folders.  For example,

        C:\Users\Administrator\Documents\Emulex\Drivers\FC-version\x64\win2022

    ]]>         Updated to driver version 14.0.534.0

    The raw driver files can be obtained by extracting the Smart Component and then extracting the Emulex installer.  Use this command:

        elxdrvr-fc-version.exe /q2 extract=2

    The extracted files are located:

        C:\Users\Administrator\Documents\Emulex\Drivers\FC-version

    Each kit folder has subsequent architecture folders with subsequent OS folders.  For example,

        C:\Users\Administrator\Documents\Emulex\Drivers\FC-version\x64\win2022

    ]]>
  • Added support for Microsoft Windows Sever 2022.
    • ]]>
  • Added support for Remote Key Management of Managed SED.
  • Added the Authority Key Identification 'security show' command in the SSA CLI for SPDM.
    • ]]>
  • Fixed an issue in SSA CLI where failed drive details were shown twice in the show config output.
  • Fixed an issue in SSA CLI where an error message was not being generated while performing an invalid modify command.
  • Fixed an issue in SSA CLI where the tool would display a Reboot required reason when modifying MRRS value to same value.
  • Fixed an issue in SSA CLI that would display an invalid error string in the show foreignmasterkeyidentifier output with Managed SEDs.
  • Updated SSA CLI to not list drivetypes that do not have the correct number of drives to modify an array with Managed SEDs.
  • Fixed an issue in SSA Scripting where a volume creation would fail when Remote SED mode was enabled and waiting for reboot.
    • ]]>         Initial Release

    ]]>
  • Added support for Superdome 3200
    • ]]>
  • Added support for Intel SPR MCC CPU
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         This product fix an issue that TCP traffic on VMs might be interrupted if PF undergoes a reset.

    ]]>         This product now supports the following new server.

    HPE ProLiant DL560 Gen11 Server
    HPE ProLiant DL110 Gen11 Server
    HPE ProLiant ML110 Gen11 Server

    ]]>
  • Optimize sensor reporting to improve failure rate - AFR (Annual Failure Rate) metrics
    • ]]>
  • Optimize sensor reporting to improve failure rate - AFR (Annual Failure Rate) metrics
    • ]]>         Supports VMware ESXi 8.0

    ]]>         Supports VMware ESXi 8.0

    ]]>         The following fixes were incorporated in this version:

    • Code optimization to save memory repo.

    • TLB exception seen while doing esp reset when expander reset was in progress.

    • Added the psoc 8.93 binary in peripheral images, updated the reveille version numbers.

    • Added whole new Delta PS-pmbus code , Updated the ESP version number.

    Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

    ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         TBD

    ]]>
  • This product enhances the RDE BEJ encoding for some MessageArgs.
  • This product removes CCM(Comprehensive Configuration Management) for the legacy driver.
  • This product removes Energy-Efficient Ethernet (EEE) from the PHY for BCM5741x adapters.
  • This product adds range validation checks to dest_port and dest_port_mask for ntuple commands.
  • This product adds to support HPE MicroServer Gen11
    • ]]>
  • This product fixes the issue of incorrect PCIe VF numbers caused by some NCSI queries for BCM5741x adapters
  • This product fixes the RDE error response for certain properties with unsupported input
  • This product fixes the problem of no RDE alert being generated when the link status changes.
    • ]]>
  • This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.
  • The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.
  • Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>
  • Added support for Microsoft Windows Server 2022,
    • ]]>
  • Bug fixes for D3-S4520/S4620 2.5" and M.2
    • ]]>
  • Fixes a false indication of rare capacitor test failure
    • ]]>
  • Fixes a false indication of rare capacitor test failure
    • ]]>
  • This product now changes default number of queues for high core count platforms
  • This product changes the default setting where the GNSS(GNSS_SUPPORT) is disabled now
  • This product now supports RHEL 9.1
    • ]]>
  • This product fixes an issue where the virtual function failed to create
  • This product fixes an issue where crash is observed when changing the bonding mode from Balance TLB to 802.3ad
  • This product fixes an issue where the traffic goes to unintended random rx_queues when number of parallel stream increased in iperf even if affinity is set
    • ]]>         This product enhanced the availability of debugfs functionality when UEFI Secure Boot is enabled

    ]]>
  • Improves data integrity
  • Decreases possibility of data corruption in certain error and timing conditions
  • Reduces the probability of hangs
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Addresses a hot plug reporting concern
  • Increased the buffer memory size used for sequential write data to resolve performance degradation seen in a RAID60 configuration
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>         It has fix code for V6 read disturb and other issues

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Problems Fixed:

    Addressed an issue where the MegaRAID controller status is displayed as "unknown" on the iLO web page.

    Known Issues:

    None]]>         Set the value of the Snoop Response Hold Off for IOAT Stack setting to 7 when the vRAN Workload Profile has been selected. This aligns with Intels performance tuning recommendation.

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Problems Fixed:

    Address an issue with some 4th Generation Intel Xeon Processors that can result in an unexpected reset with a machine check error logged to the Integrated Management Log (IML).  This issue is not unique to HPE systems.  The following is Intel’s description of the issue:  "Under complex microarchitectural conditions, the processor may experience a Caching Home Agent Table of Requests (TOR) timeout machine check exception."  This version of the System ROM will update internal processor firmware during boot.  This internal processor firmware cannot be downgraded even if the System ROM is downgraded. Using processors with different version of internal firmware is not supported.

    Addressed an issue where the speed of Kioxia EDSFF drive might be downgraded from PCIe Generation 5 to Generation 4.

    Known Issues:

    None

    ]]>         Updated to version 9.4.8.20

    ]]>         Updated to version 9.4.6.20

    ]]>         Added support for:

    Red Hat Linux 8.8

    Red Hat Linux 9.2

    SLES 15 SP5

    Updated Driver version 10.02.10.00-k1

    ]]>         Updated Driver version 10.02.08.01_k1-1

    ]]>         Fix GHC issue

    ]]>         Support Gen11 Intel servers.

    ]]>         This product fixes an issue where the firmware update failed when secure boot is enabled

    ]]>
  • This product fix an issue where it has warning message during compilation
  • This product correct an issue which the RPM metadata missing pci-id
    • ]]>
  • Fix bugs found in the previous version and improve on TTR (Time To Ready) requirement to fix device temporarily not found issue after hot-plug.
    • ]]>
  • ​Added Relaxed Ordering feature in drive FW and fixed some bugs
    • ]]>
  • Fixes an issue in previou version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on
    • ]]>
  • Added support for RHEL 9.
    • ]]>         Important : Security Hardening Enhancements - This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device firmware to this version to improve the firmware security and reliability of your device.

     

    New features and changes included in version 16.35.3006:

    • Enabled ACS for single port cards.
    • Added vPort counters after creating the LAG demux table to count kernel packets reaching all the PFs participating in the LAG.
    ]]>         The following issues have been fixed in version 16.35.3006:

    • Packet loss that occurred when restarting the transmit. 
    • An issue that prevented RoCE malformed packets (UDP packet with dest_port equal to RoCE well known udp_dport (0x4791)) from being counted on the vport_counter when the function disables RoCE (through MODIFY_NIC_VPORT_CONTEXT command).
    • A memory leakage that occurred when closing connected QPs (Type RC/UC/XRC/DC).
    • Added a missing VLAN strip.
    ]]>         Important : Security Hardening Enhancements - This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device firmware to this version to improve the firmware security and reliability of your device.

    New features and changes included in version 16.35.1012:

    • Added support for copy modify header steering action to/from the UDP field.
    • Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.
    • QoS priority trust default state can now be changed using the new nvconfig below:

        QOS_TRUST_STATE_P1
        QOS_TRUST_STATE_P2
    The values that can be used to set the default state are:
        TRUST_PORT
        TRUST_PCP
        TRUST_DSCP
        TRUST_DSCP_PCP

    ]]>         The following issues have been fixed in version 16.35.1012:

    • RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
    • PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
    • Bad configuration of number of VFs and SFs led to the consumption of too many functions and triggered a FW assert 0x888E. The reduction flows behavior was fixed to ensure the configuration does not exceed the total number of supported functions. 
    • InfiniBand L2 QP could not receive RDMA traffic occasionally.
    • Running with a debug firmware reduced security as if token was applied.
    ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         Initial Release

    ]]>         No changes and new features in version 1.12.0

    ]]>         Fixes included in version 1.12.0:

    • Fixed race condition between BIOS checking link status and LNI completing which resulted in PXE boot failures.
    • Changed the default behavior of the hfi1_eprom tool to convert the eprom format to version 2, eliminating the need to supply the -N command line argument.
    • Addressed an issue where updating the HfiPcieGen3Loader*.rom file could result in the erasure of HfiPcieGen3Loader*.efi and HFI_TYPE1*.dat files.
    ]]>         No changes and new features in version 1.11.0

    ]]>         Fixes included in version 1.11.0:

    • The following issue has been fixed in Unified Extensible Firmware Interafce (UEFI) ROM: On some platforms, the hfi1 device was not showing up in BIOS/UEFI boot menus and was not available as a PXE boot device. This was caused by the platform not loading the UEFI driver for the hfi1 adapter. 
    ]]>         The following changes and new features have been included in version 23.04-1.1.3.1

    • Starting this release, MLNX EN+RoCE drivers will adopt the following versioning naming scheme: YY.MM-x.x.x.x (i.e., Year.Month-x.x.x.x).
    • Added support for allowing the host to track various statistics for the VFs, specifically all of the Q_counters stats even if he gives the VF to a VM, through the representor Q_counters for the VF which are now exposed over the host.
    • With this feature, a kernel error log is now generated when certain fatal QP errors occur.
    • Added support for the following operating systems:
      • RHEL 9.2
      • RHEL 8.8
      • SLES15-SP5
    ]]>         The following issues have been fixed in version 23.04-1.1.3.1:

    • Installing "mlnx_tune" on Python3 did not work properly. "mlnx_tune" now supports Python3 in addition to Python2.
    • Changing traffic class via the sysfs while modifying QPs in parallel caused a deadlock.
    • Due to a bug in the emulation layer, performance degradation was experienced when running GPUDirect over Virtual Functions.
    • "debugfs" directories could not be created for representors and sub-functions, thus the log showed error for both the scenarios.
    • "knem" did not fully support RHEL8.7 and newer releases.
    ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>
  • ​​Firmware adds support for new humidity sensor
    • ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>         New release.

    ]]>
  • This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.
  • The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.
  • Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Reduced the occurrence probability of PMIC busy issue by stopping PLP capacity check to reduce i2c access to PMIC.
    • ]]>
  • Reduced the occurrence probability of PMIC busy issue. 
  • Fixed the system data error at the drive power on issue. 
  • When the PLP operation starts, the waiting Unmap request to the 4KB not-aligned host write area is canceled to be able to complete PLP correctly.
    • ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

    New features and changes included in version 20.38.1002:

    • Improved token calculation.
    • Added support for forwarding INT packets to the user application for monitoring purposes by matching the BTH acknowledge request bit (bth_a).
    ]]>         The following issues have been fixed in version 20.38.1002:

    • A link failure that occurred due to a wrong 'is_inphi_cable' indication.
    • Fixed a firmware assert that occurred when tried to verify if  the module supported  "swap".
    ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

     

    New features and changes included in version 20.37.1700:

    • A new capability enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Updated the link maintenance flow to avoid high uncorrectable error rate. 
    ]]>         No fixes in this version.

    ]]>
  • Added support for RHEL 9.
    • ]]>
  • Firmware addresses a hot plug reporting concern
    • ]]>
  • Fixed an issue of sending a command to physical devices during device discovery.
  • Fixed an issue where the OS crashes when a drive is hot removed during I/O stress test.
  • Fixed an issue where the OS crashes on aarch64 servers using the out-of-box driver during driver initialization.
  • Added sysfs entry for NUMA node in /sys/block/sdX/device. NUMA node detail is added for each exposed device similar to NVMe devices.
    • ]]>         Initial Release

    ]]>         TBD

    ]]>
  • This product enhances the RDE BEJ encoding for some MessageArgs.
  • This product removes CCM(Comprehensive Configuration Management) for the legacy driver.
  • This product removes Energy-Efficient Ethernet (EEE) from the PHY for BCM5741x adapters.
  • This product adds range validation checks to dest_port and dest_port_mask for ntuple commands.
  • This product adds to support HPE MicroServer Gen11     
    • ]]>
  • This product fixes the issue of incorrect PCIe VF numbers caused by some NCSI queries for BCM5741x adapters
  • This product fixes the RDE error response for certain properties with unsupported input
  • This product fixes the problem of no RDE alert being generated when the link status changes.
    • ]]>         This product enhanced the compatibility with firmware of CVL4.2.

    ]]>
  • This product enhanced the compatibility with firmware of CVL4.1.
  • This product now supports the following new server.

    • HPE ProLiant DL560 Gen11 Server
    HPE ProLiant DL110 Gen11 Server
    HPE ProLiant ML110 Gen11 Server

    ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9
    • ]]>
  • Optimize sensor reporting to improve failure rate - AFR (Annual Failure Rate) metrics
    • ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>         Updated to version 1.0.0.1

    ]]>         Updated to version 1.0.0.1

    ]]>         New release.

    ]]>         New release.

    ]]>         Updated to driver version 14.2.589.10-1

    ]]>         Updated to driver version 14.0.499.31

    ]]>         It has fix code for V6 Read disturb issue and other issue

    ]]>         This product fix an issue that TCP traffic on VMs might be interrupted if PF undergoes a reset.

    ]]>         This product fix an issue that TCP traffic on VMs might be interrupted if PF undergoes a reset.

    ]]>         This product enhanced the compatibility with firmware of CVL4.1.

    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         This product correct an issue which the component can't read the current driver version.

    ]]>         This product now supports HPE ProLiant Gen11 Platforms with Intel processors

    ]]>
  • Reverted OCP spec features to maintain compliance to OCP spec commands over NVMe-MI
  • Implemented real Active Measured Latency by adding OCP 2.0 C3 Log page
    • ]]>

  • This component provides support only for VMD enabled Intel VROC platform..

    • ]]>
  • OCP v2.0 feature support 
  • NVMe-MI over PCIe VDM support
    • ]]>         TBD

    ]]>
  • This product enhanced to add bnxt_re module parameter to specify the number of MSIX vectors per PF.
  • This product enhanced to add the support for rdma-core version v38, v39, v40, v41 and v24 in RoCE library.
    • ]]>
  • This product addresses an issue where System crash due to the race conditions between different bnxt_re driver operations
  • This product correct an issue which the bnxt_re driver crash or longer time to complete during unload under heavy RoCE I/O load.
  • This product correct an issue which the bnxt_re ifup initialization failed after aborted error recovery.
  • This product correct an issue which the Kernel panic when driver detect roce firmware command timeout.
  • This product correct an issue which the debugging bnxt_re printing to reduce the latency whenever the roce channel command timeout is detected.
  • This product correct an issue which ethtool -m could not dump the information for the SFF 0x1e module ID.
  • This product correct an issue which RoCE bandwidth very lower when load driver with no link present and speed forced to 10G.
  • This product correct an issue which system crash when enabling VF and vswitch bridging in a repeated cycle.
    • ]]>         Initial release.

    ]]>
  • Adds support for a second source drive pre-amp, and improves reliability with an updated direct offline scan algorithm.
    • ]]>         Added support for:

    Red Hat Linux 8.8

    Red Hat Linux 9.2

    SLES 15 SP5.

    Updated to version 14.2.589.4-1

    ]]>         Updated to version 14.0.499.28-1

    ]]>         This product now supports  ResetToDefault property(RDE Port Schema).

    ]]>         This product addresses an issue where InterfaceEnabled property is read only and it can't patch this property

    ]]>
  • This product now supports RDE Read and Write operations.
  • This product now supports Debug Dump feature.
  • This product now supports new parameters when software requesting on Port 0(via AQ the connectivity type)
    • ]]>         Added support for:

    Red Hat Linux 8.8

    Red Hat Linux 9.2

    SLES 15 SP5

    Updated the kit to version 6.0.0.0-19

    ]]>         Updated the kit to version 6.0.0.0-18

    ]]>
  • This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.
  • The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.
  • Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.
    • ]]>
  • This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.
  • The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.
  • Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>         TBD

    ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>
  • DMTF PLDM Redfish Device Enablement enhancements
    • Support Volume Creation and Deletion by the following Redfish requests
      • POST VolumeCollection
      • DELETE Volume
      • GET Volume Capabilities
    • Added support for the following Redfish ACTION requests:
      • POST Storage.ResetToDefaults
      • POST Volume.Initialize
      • POST Drive.SecureErase
    • Added support for Redfish PATCH requests for the following properties:
      • PATCH Volume.DedicatedSpareDrives
      • PATCH Volume.DisplayName
      • PATCH Volume.ReadCachePolicy
      • PATCH Volume.WriteCachePolicy
      • PATCH Drive.HotspareType
      • PATCH Drive.LocationIndicatorActive
      • PATCH Drive.WriteCacheEnabled
  • Support DMTF PLDM firmware update for drive
    • ]]>
  • Fix a00127934en_us: HPE ProLiant Gen10 Plus Servers - Unable to Switch From LKM to EKM With MR Controllers When Boot Time Password is Set
  • Fix an issue that Sanitize Block Erase on NVMe drive along with shutdown sequence may cause assertion in firmware.
  • Fix an issue that GET Volume query from REST client may fail when multiple Volumes are configured on the controller
  • Fix an issue that firmware throws error when setting WCE (Disk Write Cache) = 0 for JBOD drive.
  • Fix an issue that HDD sensor shows temperature on 14-HD Max when there is no drive installed.
  • Fix an issue that HII page may hang while there is pinned cache then do drives initialization and View Server Profile.
  • Fix a rare issue that controller may not getting discovered when there is power loss during cache restoration from a previous power loss.
  • Fix an issue that controller may hang and Online Controller Reset is triggered after running "storcli /cx set debug reset all" and then "storcli /cx get snapdump".
  • Fix an issue that enable security on logical drive may enable security on other unrelated drives which were configured as Dedicated Spare drive for other secured logical drive before.
  • Fix an issue that drive running sanitize overwrite may become Unconfigured Bad Unsupported after a cold boot
  • Fix a rare issue that firmware may hit assertion failure when a drive causes IO issue and fails.
  • Fix an issue that IML 1906 may be incorrectly logged when doing config clear and reboot.
  • Fix an issue that NVMe drives may move to Unconfigured Bad state from Unconfigured Good during driver unload-reload.
  • Fix an issue that SPDM GET_MEASUREMENTS command signature verification is failing at iLO
    • ]]>
  • Reduced the occurrence probability of PMIC busy issue by stopping PLP capacity check to reduce i2c access to PMIC.
    • ]]>
  • Reduced the occurrence probability of PMIC busy issue by stopping PLP capacity check to reduce i2c access to PMIC.
    • ]]>
  • Added support for improving secure erase time for disks supporting the WRITE SAME command.
  • Added support for switching persistent event log policy without clearing the existing event logs.
  • Added support for Remote Key Management of Managed SED.
  • Added support for 256 bytes Key Management Service (KMS) key identifier.
  • Added support for reporting surface scan metrics for host management tools.
  • Added support to allow re-enabling logical drive with rebuild option.
  • Introduce an HII option labeled 'Configure Controller UEFI Driver Health Reporting' within the 'Configure Controller Settings' menu to provide the capability to enable or disable the reporting of configuration errors and driver health.
  • Introduce an HII option labeled 'Controller Password State' within the CBE (Controller-Based Encryption) settings, enabling the actions to unset, temporarily suspend, and resume the controller password.
  • Updated the Redfish resource to align with the DMTF 2022.2 schema bundle, including the incorporation of Redfish annotations.
  • Adjusted the severity for Redfish Volume Status.Health state and DriveOffline alert for Foreign SED.
  • Create Redfish Volumes with a RAIDType set to 'None' for HBA (Host Bus Adapter) drives.
    • ]]>
  • Fixed issues related to spare drive functionality.
  • Fixed issues pertaining to Self-Encrypting Drive (SED) functionality.
  • Fixed an issue where rebuild was being reiterated continuously and not progressing.
  • Fixed controller detection issues during system boot, including rare cases that could lead to PSOD or RSOD errors.
  • Fixed an issue where the SR932i-p Gen11 controller was not assigned an EID.
  • Fixed an issue where rebuild was being reiterated continuously and not progressing.
  • Fixed an issue where Redfish events of battery and WriteCache do not meet requirements.
  • Fixed an issue where firmware incorrectly reported unrecoverable media errors.
  • Fixed an issue where the surface scan progress status is displayed as "In progress" even after disabling the surface scan on the controller.
  • Fixed an issue where rebuild was being reiterated continuously and not progressing.
  • Fixed an issue related to the failure of the clear controller configuration command.
  • Fixed an issue where an Uncorrectable error PSOD observed after power on.
  • Fixed an issue where the Unique ID of different SATA disks is the same in Windows.
  • Fixed an issue of power surge when too many SATA drives are spinning up simultaneously.
  • Fixed issues where logical drives were lost after a controller reset to factory defaults, especially when the 'preserve logical drive' option was enabled, and after an abrupt reboot where the controller reset to factory defaults, causing RAID loss.
  • Fixed migrating a SmartCache when destination controller has existing logical drive.
  • Fixed inaccuracies in SES enclosure behavior during hot-adding and hot-removing procedures.
  • Fixed an issue where the controller was providing incorrect mode page information regarding the Write Cache attribute of NVMe drives.
  • Fixed an issue causing system freezes during boot after enabling Secured-Core (DMAr) in RBSU.
  • Fixed an issue where the BatteryMissing event was not being sent when the battery was removed prior to boot.
  • Fixed an issue where a DriveOffline Redfish alert is not sent when a Drive resource initiated a sanitize operation.
  • Fixed an issue where the controller's attempt to update an unflashable UBM resulted in an error report.
  • Fixed an issue where an unflashable SMP PSOC (System Management Processor Programmable System-on-Chip) device was incorrectly appearing in the Type 5 downstream devices.
  • Fixed an issue where driver health error messages were not displayed when the system language was changed to a non-English language.
  • Fixed an issue of incorrectly reporting the WriteCachePolicy for a Volume resource as "ProtectedWriteBack" when the cache was temporarily disabled.
  • Correct Redfish properties when backup power source is removed.
  • Fixed an issue where the controller failed to report storage information in the absence of physical drives.
  • Fixed an issue where an unexpected 'BatteryCharging' event was reported when no battery was present.
    • ]]>         Initial Release

    ]]>         Added Gen11 support

    ]]>
  • Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.
    • ]]>
  • Update the component version to resolve host incompatibility with vLCM Image after updating with predefined baseline.
  • Fix OS upgrade failure due to unreplaced Gen9 AMS CLI component.
    • ]]>
  • Added support for Remote Key Management of Managed SED.
  • Added the Authority Key Identification 'security show' command in the SSA CLI for SPDM.
    • ]]>
  • Fixed an issue in SSA CLI where failed drive details were shown twice in the show config output.
  • Fixed an issue in SSA CLI where an error message was not being generated while performing an invalid modify command.
  • Fixed an issue in SSA CLI where the tool would display a Reboot required reason when modifying MRRS value to same value.
  • Fixed an issue in SSA CLI that would display an invalid error string in the show foreignmasterkeyidentifier output with Managed SEDs.
  • Updated SSA CLI to not list drivetypes that do not have the correct number of drives to modify an array with Managed SEDs.
  • Fixed an issue in SSA Scripting where a volume creation would fail when Remote SED mode was enabled and waiting for reboot.
    • ]]>         Initial Release

    ]]>         TBD

    ]]>         This product now supports HPE ProLiant Gen11 Platforms with Intel processors

    ]]>         The following changes and new features have been included in version 23.04-1.1.3.1

    • Starting this release, MLNX EN+RoCE drivers will adopt the following versioning naming scheme: YY.MM-x.x.x.x (i.e., Year.Month-x.x.x.x).
    • Added support for allowing the host to track various statistics for the VFs, specifically all of the Q_counters stats even if he gives the VF to a VM, through the representor Q_counters for the VF which are now exposed over the host.
    • With this feature, a kernel error log is now generated when certain fatal QP errors occur.
    • Added support for the following operating systems:
      • RHEL 9.2
      • RHEL 8.8
      • SLES15-SP5
    ]]>         The following issues have been fixed in version 23.04-1.1.3.1:

    • Installing "mlnx_tune" on Python3 did not work properly. "mlnx_tune" now supports Python3 in addition to Python2.
    • Changing traffic class via the sysfs while modifying QPs in parallel caused a deadlock.
    • Due to a bug in the emulation layer, performance degradation was experienced when running GPUDirect over Virtual Functions.
    • "debugfs" directories could not be created for representors and sub-functions, thus the log showed error for both the scenarios.
    • "knem" did not fully support RHEL8.7 and newer releases.
    ]]>         No new features or changes have been included in version 5.8.

    ]]>         The following issues have been fixed in version 5.8:

    • The redundant freeing of a list item could lead to memory corruption, potentially causing the application to crash or incorrect traffic handling.
    • The host driver probe did not check whether there are existing SFs which are present in the device, causing the host driver to not recreate those SFs.
    • The kernel went into panic mode if there were multiple encapsulations and not all neighbors were valid.
    ]]>         TBD

    ]]>
  • This product enhanced to add bnxt_re module parameter to specify the number of MSIX vectors per PF.
  • This product enhanced to add the support for rdma-core version v38, v39, v40, v41 and v24 in RoCE library.
  • This product enhanced to add the compatibility with SLES15-SP4.
    • ]]>
  • This product addresses an issue where System crash due to the race conditions between different bnxt_re driver operations
  • This product correct an issue which the bnxt_re driver crash or longer time to complete during unload under heavy RoCE I/O load.
  • This product correct an issue which the bnxt_re ifup initialization failed after aborted error recovery.
  • This product correct an issue which the Kernel panic when driver detect roce firmware command timeout.
  • This product correct an issue which the debugging bnxt_re printing to reduce the latency whenever the roce channel command timeout is detected.
  • This product correct an issue which ethtool -m could not dump the information for the SFF 0x1e module ID.
  • This product correct an issue which RoCE bandwidth very lower when load driver with no link present and speed forced to 10G.
  • This product correct an issue which system crash when enabling VF and vswitch bridging in a repeated cycle.
  • This product correct an issue which the RPM metadata missing pci-id
    • ]]>         The following changes and new features have been included in version 23.04-1.1.3.1

    • Starting this release, MLNX EN+RoCE drivers will adopt the following versioning naming scheme: YY.MM-x.x.x.x (i.e., Year.Month-x.x.x.x).
    • Added support for allowing the host to track various statistics for the VFs, specifically all of the Q_counters stats even if he gives the VF to a VM, through the representor Q_counters for the VF which are now exposed over the host.
    • With this feature, a kernel error log is now generated when certain fatal QP errors occur.
    • Added support for the following operating systems:
      • RHEL 9.2
      • RHEL 8.8
      • SLES15-SP5
    ]]>         The following issues have been fixed in version 23.04-1.1.3.1:

    • Installing "mlnx_tune" on Python3 did not work properly. "mlnx_tune" now supports Python3 in addition to Python2.
    • Changing traffic class via the sysfs while modifying QPs in parallel caused a deadlock.
    • Due to a bug in the emulation layer, performance degradation was experienced when running GPUDirect over Virtual Functions.
    • "debugfs" directories could not be created for representors and sub-functions, thus the log showed error for both the scenarios.
    • "knem" did not fully support RHEL8.7 and newer releases.
    ]]>         No new features or changes have been included in version 5.8.

    ]]>         The following issues have been fixed in version 5.8:

    • The redundant freeing of a list item could lead to memory corruption, potentially causing the application to crash or incorrect traffic handling.
    • The host driver probe did not check whether there are existing SFs which are present in the device, causing the host driver to not recreate those SFs.
    • The kernel went into panic mode if there were multiple encapsulations and not all neighbors were valid.
    ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>         See the iSUT Release Notes for information about the enhancements added in this release

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         See the iSUT Release Notes for information about the enhancements added in this release

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         New features and changes included in version 26.37.1700:

    • Modified the RDE behavior to return an error if the chassis ID subtype is AgentId, or Port ID subtype is ChassisComp.
    • Enabled VF LAG hash mode. The LAG_RESOURCE_ALLOCATION mlxconfig field is now modifiable.
    • A new capability enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Added a flow rule that enables offloading of multicast traffic by broadcasting it to multi-Flow-Table in FDB.
    • Enables a smooth and statically switch between PCC algorithms. In addition, the user can now switch between PCC algorithms while running traffic.
    • Added support for 32 actions in the header modify pattern using bulk allocation.
    ]]>         The following issues have been fixed in version 26.37.1700:

    • An issue that prevented the adapter card from handling WoL packets when the host powered up directly into the standby mode.
    • CNP received, handled, and ignored counters in the hardware counters could not work after moving to Programmable Congestion Control mode.
    ]]>         New Features and Changes in Version 26.35.1012:

    • Added support for copy modify header steering action to/from the UDP field.
    • Added the following resource dump segments:

    SEG_HW_STE_FULL that includes dump to STE and all its dependencies
    SEG_FW_STE_FULL that include dump to FW_STE and to HW_STE_FULL in range

    • As the software requires additional space before and after a packet is scattered for its processing for stridden RQ, the hardware will allocate the required room while scattering packets to spare a copy. 
    • QoS priority trust default state can now be changed using the new nvconfig below:

    QOS_TRUST_STATE_P1
    QOS_TRUST_STATE_P2
    The values that can be used to set the default state are:
    TRUST_PORT
    TRUST_PCP
    TRUST_DSCP
    TRUST_DSCP_PCP

    ]]>         The following issues have been fixed in version 26.35.1012:

    • The patch to the RDE LLDPEnable property in Port schema would not be updated after the host reboot.
    • RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
    • PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
    • PCIe SKP OS generation interval for Gen1 and Gen2.
    ]]>         This product enhanced the compatibility with firmware of CVL4.2.

     

    ]]>         This product fix an issue that TCP traffic on VMs might be interrupted if PF undergoes a reset.

    ]]>         The following fixes were incorporated in this version:

    • Code optimization to save memory repo.

    • TLB exception seen while doing esp reset when expander reset was in progress.

    • Added the psoc 8.93 binary in peripheral images, updated the reveille version numbers.

    • Added whole new Delta PS-pmbus code , Updated the ESP version number.

    Please refer to the Release Notes for the complete listing of fixes, enhancements, known issues and work-arounds corresponding to this firmware.

    ]]>         The following changes and new features have been included in version 23.04-1.1.3.1

    • Starting this release, MLNX EN+RoCE drivers will adopt the following versioning naming scheme: YY.MM-x.x.x.x (i.e., Year.Month-x.x.x.x).
    • Added support for allowing the host to track various statistics for the VFs, specifically all of the Q_counters stats even if he gives the VF to a VM, through the representor Q_counters for the VF which are now exposed over the host.
    • With this feature, a kernel error log is now generated when certain fatal QP errors occur.
    • Added support for the following operating systems:
      • RHEL 9.2
      • RHEL 8.8
      • SLES15-SP5
    ]]>         The following issues have been fixed in version 23.04-1.1.3.1:

    • Installing "mlnx_tune" on Python3 did not work properly. "mlnx_tune" now supports Python3 in addition to Python2.
    • Changing traffic class via the sysfs while modifying QPs in parallel caused a deadlock.
    • Due to a bug in the emulation layer, performance degradation was experienced when running GPUDirect over Virtual Functions.
    • "debugfs" directories could not be created for representors and sub-functions, thus the log showed error for both the scenarios.
    • "knem" did not fully support RHEL8.7 and newer releases.
    ]]>         No new features or changes have been included in version 5.8.

    ]]>         The following issue have been fixed in verson 5.8(A):

    • On SuSE Linux Enterprise Server 15SP4 errata kernel version 5.14.21-150400.24.11.1 and later the HPE Mellanox RoCE (RDMA over Converged Ethernet) Driver 5.8 fails to load correctly because of symbol mismatch in the kernel modules and weak-updates failure. The version 5.8(A) is built against the errata kernel version 5.14.21-150400.24.11.1 and fixes the above issue on this and the later SuSE Linux Enterprise Server 15SP4 errata kernel versions.

    The following issues have been fixed in version 5.8:

    • The redundant freeing of a list item could lead to memory corruption, potentially causing the application to crash or incorrect traffic handling.
    • The host driver probe did not check whether there are existing SFs which are present in the device, causing the host driver to not recreate those SFs.
    • The kernel went into panic mode if there were multiple encapsulations and not all neighbors were valid.
    ]]>
  • Added support for RHEL 9
    • ]]>
  • Fixes an intermittent issue where the incorrect model number can be reported during spin-up.
    • ]]>         New features and changes included in version 22.37.1700:

    • Added a safety mechanism to prevent the link from to getting stuck when receiving bad tuning results. In this case, the linkup flow is restarted and the mechanism retries to raise the link.
    • Improved rate limit token re-distribution algorithm.
    • Improved non-consumed bandwidth re-distribution.
    • Added mergeable buffer support (VIRTIO_NET_F_MRG_RXBUF in virtio spec) for VDPA kernel mode to improve performance in case of large MTU such as 9K. The feature is disabled by default and must be manually enabled while creating or modifying the virtio device.

        Note: For best performance, it is NOT recommended to enable the feature if the VDPA MTU is set to the default value (1500).

    • A new capability that enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Added a flow rule that enables offloading of multicast traffic by broadcasting it to multi-Flow-Table in FDB.
    • Enables a smooth and statically switch between PCC algorithms. In addition, the user can now switch between PCC algorithms while running traffic.
    • Added support for running PCC firmware trace without saving and sending the DB strings to the tool with the following changes:
      • Added new string section to the user PCC image creation tool
      • Added the new PCC DB strings to MTRC access registers output
      • On the tool's part: added support to reading the string.db using the MTRC access registers
    • Added support for 32 actions in the header modify pattern using bulk allocation.
    • The software can explicitly set the SL of an RTT response packet, instead of it being taken from the RTT request packet's SL. The RTT response packet SL may be set/queried via the CONGESTION_CONTROL_HCA_NP_PARAMETER MAD.
    ]]>         The following issues have been fixed in version 22.37.1700:

    • No ping in NODNIC VF when VLAN stripping was enabled.
    • vDPA application initialization failed due to virtual queue creation failure. The failure came with the "0x8f7a: ring address translate failed" assert which indicates incorrect permission supplied by QEMU for virtual ring memory.
    • CNP received, handled, and ignored counters in the hardware counters could not work after moving to Programmable Congestion Control mode.
    ]]>         New features and changes included in version 22.35.1012:

    • Improved both TP1a compliance and Physical-layer performance. TX and PLL settings were changed to comply with IEEE 802.3bs TP1a and improved link margins. 
    • Enabled the firmware to distribute loopback QPs/SQs between all LAG ports during the initial distribution in steering LAG.
    • Changed the Tx setting for optics HDR to improve compliance margins.
    • HPCC related configurations are now supported via the mlxconfig utility.
    • Added support for copy modify header steering action to/from the UDP field.
    • Added support for range based lookup. This new capability is available using the following new PRM command:

    GENERATE WQE which receives GTA WQE, the command supports "match on range" and num_hash_definer=[1,2] and num_match_ste=[1,2].
    For further information, refer to section "RTC Object Format" in the PRM.

    • Added support for RoCE based VM migration.
    • Added the following resource dump segments:

    SEG_HW_STE_FULL that includes dump to STE and all its dependencies
    SEG_FW_STE_FULL that include dump to FW_STE and to HW_STE_FULL in range

    • As the software requires additional space before and after a packet is scattered for its processing for stridden RQ, the hardware will allocate the required room while scattering packets to spare a copy. 
    • Improved security offload's Connections per Second (CPS) rate using the general object DEK (PSP TLS etc).
    • Added support for pre-copy commands in VF migration flow in order to reduce the migration downtime.
    • Optimized performance to support full VF migration flow.
    • Increased the VirtIO hardware offload message rate to 20/20 MPPS for 256 virtual devices by optimizing the datapath application code.
    • Enabled ADP timer to allow the user to configure RC or DC qp_timeout values lower than 16.
    • QoS priority trust default state can now be changed using the new nvconfig below:

    QOS_TRUST_STATE_P1
    QOS_TRUST_STATE_P2
    The values that can be used to set the default state are:
    TRUST_PORT
    TRUST_PCP
    TRUST_DSCP
    TRUST_DSCP_PCP

    ]]>         The following issues have been fixed in version 22.35.1012:

    • RDE (Redfish) PATCH operation to LLDPTransmit properties "ManagementAddressIPv4", "ManagementAddressIPv6" and "ManagementAddressMAC" were applied only in the first attempt, but failed in the next.
    • Commands sent by the MLNX_OFED driver to the NIC would fail when loading the VirtIO driver. 
    • A firmware limitation caused enabling tx_port_ts to result in syndrome 0x5d2974.
    • PLDM AEN event receiver media was changed unexpectedly and destination BDF was overridden with garbage when some PLDM packet were received from the SMBus layer.
    • PCIe SKP OS generation interval for Gen1 and Gen2.
    • CPU handling synchronization required separation (run ptp4l with taskset -c [cpu #] prefix) while running heavy traffic. 
    ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

    New features and changes included in version 20.38.1002:

    • Improved token calculation.
    • Added support for forwarding INT packets to the user application for monitoring purposes by matching the BTH acknowledge request bit (bth_a).
    ]]>         The following issues have been fixed in version 20.38.1002:

    • A link failure that occurred due to a wrong 'is_inphi_cable' indication.
    • Fixed a firmware assert that occurred when tried to verify if  the module supported  "swap".
    ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

     

    New features and changes included in version 20.37.1700:

    • A new capability enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Updated the link maintenance flow to avoid high uncorrectable error rate. 
    ]]>         No fixes in this version.

    ]]>         Enable Redfish Write for Drive.SecureErase and Storage.ResetToDefault. Users are able to reset the controller through PLDM. 

    ]]>         Enable Redfish Write for Drive.SecureErase and Storage.ResetToDefault. Users are able to reset the controller through PLDM. 

    ]]>         TBD

    ]]>
  • Added support for Microsoft Windows Server 2022
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>         Updated to version 1.0.0.1

    ]]>         Updated to version 1.0.0.1

    ]]>
  • Added support for Gen10/Gen10 Plus platforms
    • ]]>
  • Driver update
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         TBD

    ]]>
  • This product enhanced optimize drvier around user data copy. 
  • This product enhanced driver warning messages are thrown when driver reload.
  • This product enhanced to support XDP multibuffer.
  • This product enhanced ethtool to support CMIS 4.0 and backwards compatibility apart from compat changes.
    • ]]>
  • This product addresses an issue where System crash on running ethtool self test in loop on multiple adapter ports
  • This product addresses an issue where MSIX collision between L2 and RoCE drivers.
  • This product addresses an issue where Devlink reload command failed.
  • This product correct an issue which unable to recover from FW crash triggered by bnxtnvm fwcli 'crash fw_assert'.
  • This product correct an issue which the call traces while unloading bnxt_en and bnxt_re driver
  • This product correct an issue which ethtool -S crash when firmware is unhealthy
  • This product correct an issue which rdev allocation '__flush_work' issue by doing initialization for kernel workqueue.
    • ]]>         Added support for:

    Red Hat Linux 8.8

    Red Hat Linux 9.2

    SLES 15 SP5.

    Updated to version 14.2.589.4-1

    ]]>         Updated to version 14.0.499.28-1

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Problems Fixed:

    Addressed an issue where the MegaRAID controller status is displayed as "unknown" on the iLO web page.

    Known Issues:

    None]]>         Set the value of the Snoop Response Hold Off for IOAT Stack setting to 7 when the vRAN Workload Profile has been selected. This aligns with Intel’s performance tuning recommendation.

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Problems Fixed:

    Address an issue with some 4th Generation Intel Xeon Processors that can result in an unexpected reset with a machine check error logged to the Integrated Management Log (IML).  This issue is not unique to HPE systems.  The following is Intel’s description of the issue:  "Under complex microarchitectural conditions, the processor may experience a Caching Home Agent Table of Requests (TOR) timeout machine check exception."  This version of the System ROM will update internal processor firmware during boot.  This internal processor firmware cannot be downgraded even if the System ROM is downgraded. Using processors with different version of internal firmware is not supported.

    Addressed an issue where the speed of Kioxia EDSFF drive might be downgraded from PCIe Generation 5 to Generation 4.

    Known Issues:

    None

    ]]>         Updated to driver version 14.2.589.10-1

    ]]>
  • Improves data integrity
  • Decreases possibility of data corruption in certain error and timing conditions
  • Reduces the probability of hangs and provide a minor performance improvement
    • ]]>
  • Fixed an issue where the random drives in the system were going offline after a hot plug and reboot.
    • ]]>         Initial Release

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Problems Fixed:

    Address an issue that can result in a Red Screen of Death (RSOD) and hang during system boot or a hang during system boot without an RSOD. This issue can occur on systems utilizing the v1.32 or v1.40 System ROM revision and iLO Firmware revision v1.50. The v1.32 System ROM added a boot-time reduction capability (which also required iLO Firmware revision v1.50) which resulted in the boot-time RSOD and/or hang. This capability has been removed in this revision of the System ROM.

    Addressed an issue where one-time boot did not work properly after setting one-time boot device from iLO web or via Redfish.

    Known Issues:

    None]]>         Removed "NUMA memory domains per socket" selection item "Auto" from RBSU, because value of Auto option is actually set to one memory domain per socket. Set display default to "One memory domain per socket".

    Added "NVMe PCIe Resource Padding" option under "Advanced PCIe Configuration" in RBSU. The option is for fixing a failure to hot add NVMe drive to empty slot under OSes such as VMware. The option can be set from Redfish URI "/redfish/v1/systems/1/bios/settings/" with property "PciResourcePadding".

    ]]>         Important Notes:

    This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.8 for AMD 4th Generation EPYC processors.

    Firmware Dependencies:

    None

    Problems Fixed:

    This revision of the System ROM includes the revision of the OpenSSL library 1.1.1u update which provides mitigation for and security vulnerabilities documented as CVE-2023-2650.

    Addressed an issue where the unsupported DIMM population IML will report an incorrect processor number on dual-processor systems.

    Addressed an issue where the SMBIOS type 197 might contain an incorrect format value of xGMI speed.

    Addressed an issue where the CXL root bridge was missing from SMBIOS type 9.

    Addressed an issue where dmidecode indicates 4 power supplies are installed when only 2 power supplies are actually installed.

    Addressed an issue where number of "Internal L3 cache" displayed under RBSU information page is not correct.

    Addressed an issue where the System Health LED is illuminated Red for all memory configuration error cases. Some memory configuration error cases are not critical and should have the System Health LED illuminated Amber.

    Known Issues:

    None]]>         New release.

    ]]>         New release.

    ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device firmware to this release to improve the firmware security and reliability of your device.
     
    New features and changes included in version 28.38.1002:

    • Added a new field/slot ID to PRS  pcie_cfg_data.pci_cfg_space.pciex.pcie_switch_ini_defined_base_slot_id = 3 to define a specific slot number for GPU bridge DSP.
    • Improved token calculation.
    • Added support for NC-SI channel on both ports.
    • Changed the protection mechanism for BAR configuration.
    • Updated the SX root to work with driverless mode in vport0 gvmi teardown.
    • Added support to the metadata reg_c 8-11 (packet fields) for matching and modifying the header, and Advanced Steering Operation (ASO) actions.
    • Added support for forwarding INT packets to the user application for monitoring purposes by matching the BTH acknowledge request bit (bth_a).
    • Implemented NVIDIA NC-SI OEM Commands:

        Get Electrical Sensor Count (command 0x13, parameter 0x6)
        Gel Electrical Sensor (command 0x13, parameter 0x7)
        Get Electrical Sensors (command 0x13, parameter 0x8)

    • Improved the IPsec CPS by using bulk allocation.

        For cases in which log_obj_range == 0, single IPSEC object will be allocated and initialized as before keeping backward compatibility.
        For better performance, it is recommended to work with IPsec bulk allocation and to initialize IPsec ASO context not via the firmware but via the hardware using ASO WQE.

    • Added support for a new value for coredump_type field in DPA_PROCESS_COREDUMP, [FIRST_ERROR_THREAD_DUMP (1).].
    ]]>         The following issues have been fixed in version 28.38.1002:

    • Fixed SPDM measurements signature.
    • An issue that prevented the system from detecting the PCIe device during slot DC power cycle tests.
    • Upgrading from firmware v28.36.1010 and below to v28.38.1002 no longer requires an upgrade to an intermediate version.
    • Updated the plug in/out events' reporting method to report only when the last recorded event is the opposite of the current event.
    • Fixed the SPDM operations order according to the spec. v1.1.0.
    • An issue that caused a packet with invalid/bad padcount to be silently dropped instead of sending a bad nack error.
    • Wrong credits configuration that occurred when MAX_ACC_OUT_READ was configured.
    • A rare deadlock case between 2 DC packets in the RX side.
    • A QoS host port rate limit shaper inaccuracy that occurred when the shaper was configured via the QSHR access register.
    • When using ConnectX-7 adapter card as InfiniBand, the port must be configured to use the Auto-Negotiation mode.
    ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device firmware to this release to improve the firmware security and reliability of your device.
     
    New features and changes included in version 28.37.1700:

    • Removed the option to clear "Tx disable cap" for all non-baseT SFP modules.
    • Added a split mask verification process to check whether or not a module is split in HCA. 
    • Updated the NEGOTIATE_ALGORITHMS response according to the SPDM specification.
    • Added the option to clear the DPC registers after warm reboot.
    • Changed the initial Tx preset configuration for the DownStream port (DSP).
    • Added mergeable buffer support (VIRTIO_NET_F_MRG_RXBUF in virtio spec) for VDPA kernel mode to improve performance in case of large MTU such as 9K. The feature is disabled by default and must be manually enabled while creating or modifying the virtio device.

    Note: For best performance, it is NOT recommended to enable the feature if the VDPA MTU is set to the default value (1500).

    • A new capability that enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Added a flow rule that enables offloading of multicast traffic by broadcasting it to multi-Flow-Table in FDB.
    • Selective repeat improves network utilization in case of a lossy fabric. This features is enabled by default.
    • Added support for dynamic MSIX modification on a VF NVME device emulation.

    If a PF NVME device emulation is created with dynamic_vf_msix_control = 1, then the dynamic_vf_msix_reset can set the PF device emulation's VF MSIX number to 0. The num_msix is used in the modified VF device emulation to modify the MSIX number of the VF device emulation.

    • Enabled IB CC per Service Level (SL) for RC/UC on the HCA side.

    Now different SLs can be configured to be CC on/off according to the bitmask decided by the software.

    • Optimizes the ATC configuration dynamically based on the returned pages of the ATS translation requests that have been made.
    • Enables a smooth and statically switch between PCC algorithms. In addition, the user can now switch between PCC algorithms while running traffic.
    • Added support for 32 actions in the header modify pattern using bulk allocation.
    • The software can explicitly set the SL of an RTT response packet, instead of it being taken from the RTT request packet's SL. The RTT response packet SL may be set/queried via the CONGESTION_CONTROL_HCA_NP_PARAMETER MAD.
    ]]>         The following issues have been fixed in version 28.37.1700:

    • Firmware crashed when setting large payload length values (more than ~1500) in NC-SI command's header.
    • Interface type was shown as "unsupported" in CMIS modules.
    • Fixed the configuration of the TS1s sent by the DownStream port (DSP) when moving to EQLZ.ph2.
    • PLDM firmware update process failed in case 1304 bytes chunk size is chosen.
    • An issue that occurred during secure firmware update when decrypting and authenticating each chunk of data using its authentication tag. The issue appeared when the main code chunk was split between the user chunks and any GCM operation (e.g., flash read with decryption). This GCM operation broke the GCM context for main chunk authentication and therefore failed. 
    • CNP received, handled, and ignored counters in the hardware counters could not work after moving to Programmable Congestion Control mode.
    • Hardware failed to handle an error flow that occurred when accessing the DPA cluster L2 cache from the firmware processor. In this case the firmware processor hardware requested a VA=>PA translation from the internal mmio, and the address translation was broken by the mmio on the 4K page boundary.
    • Hardware failed to consume Port-VL and credits, which consequently blocked traffic from being transmitted due to a race condition between the firmware and the hardware when accessing the chip memory (CR space).
    ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>         Support HPE ML30 and DL20 Gen11 server.

    ]]>
  • DMTF PLDM Redfish Device Enablement enhancements
    • Support Volume Creation and Deletion by the following Redfish requests
      • POST VolumeCollection
      • DELETE Volume
      • GET Volume Capabilities
    • Added support for the following Redfish ACTION requests:
      • POST Storage.ResetToDefaults
      • POST Volume.Initialize
      • POST Drive.SecureErase
    • Added support for Redfish PATCH requests for the following properties:
      • PATCH Volume.DedicatedSpareDrives
      • PATCH Volume.DisplayName
      • PATCH Volume.ReadCachePolicy
      • PATCH Volume.WriteCachePolicy
      • PATCH Drive.HotspareType
      • PATCH Drive.LocationIndicatorActive
      • PATCH Drive.WriteCacheEnabled
  • Support DMTF PLDM firmware update for drive
    • ]]>
  • Fix a00127934en_us: HPE ProLiant Gen10 Plus Servers - Unable to Switch From LKM to EKM With MR Controllers When Boot Time Password is Set
  • Fix an issue that Sanitize Block Erase on NVMe drive along with shutdown sequence may cause assertion in firmware.
  • Fix an issue that GET Volume query from REST client may fail when multiple Volumes are configured on the controller
  • Fix an issue that firmware throws error when setting WCE (Disk Write Cache) = 0 for JBOD drive.
  • Fix an issue that HDD sensor shows temperature on 14-HD Max when there is no drive installed.
  • Fix an issue that HII page may hang while there is pinned cache then do drives initialization and View Server Profile.
  • Fix a rare issue that controller may not getting discovered when there is power loss during cache restoration from a previous power loss.
  • Fix an issue that controller may hang and Online Controller Reset is triggered after running "storcli /cx set debug reset all" and then "storcli /cx get snapdump".
  • Fix an issue that enable security on logical drive may enable security on other unrelated drives which were configured as Dedicated Spare drive for other secured logical drive before.
  • Fix an issue that drive running sanitize overwrite may become Unconfigured Bad Unsupported after a cold boot
  • Fix a rare issue that firmware may hit assertion failure when a drive causes IO issue and fails.
  • Fix an issue that IML 1906 may be incorrectly logged when doing config clear and reboot.
  • Fix an issue that NVMe drives may move to Unconfigured Bad state from Unconfigured Good during driver unload-reload.
  • Fix an issue that SPDM GET_MEASUREMENTS command signature verification is failing at iLO
    • ]]>         This product now supports  ResetToDefault property(RDE Port Schema).

    ]]>         This product addresses an issue where InterfaceEnabled property is read only and it can't patch this property

    ]]>
  • This product now supports RDE Read and Write operations.
  • This product now supports Debug Dump feature.
  • This product now supports new parameters when software requesting on Port 0(via AQ the connectivity type)
    • ]]>
  • Updated supported platforms
    • ]]>
  • Added support for Intel platforms
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>         This product now supports Red Hat Enterprise Linux 9 Update 1.

    ]]>         TBD

    ]]>         Added support for:

    Red Hat Linux 8.8

    Red Hat Linux 9.2

    SLES 15 SP5

    Updated Driver version 10.02.10.00-k1

    ]]>         Updated to driver version 10.02.07.01-k1

    ]]>
  • Updated supported platforms
    • ]]>
  • Added support for Intel platforms
    • ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

    New features and changes included in version 20.38.1002:

    • Improved token calculation.
    • Added support for forwarding INT packets to the user application for monitoring purposes by matching the BTH acknowledge request bit (bth_a).
    ]]>         The following issues have been fixed in version 20.38.1002:

    • A link failure that occurred due to a wrong 'is_inphi_cable' indication.
    • Fixed a firmware assert that occurred when tried to verify if  the module supported  "swap".
    ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

     

    New features and changes included in version 20.37.1700:

    • A new capability enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Updated the link maintenance flow to avoid high uncorrectable error rate. 
    ]]>         No fixes in this version.

    ]]>         This product now add message when set VF's MAC Address

    ]]>
  • This product enhanced the wating time to wait MTU change.
  • This product enhanced ability to turn off CRC stripping for VF
    • ]]>
  • This product fixes an issue where it has race condition between iavf_open and iavf_handle_hw_reset
  • This product fixes an crash issue in iavf_suspend
  • This product fixes VF stuck in reset.
  • This product fixes an issue where it has conflict with Mellanox or other network drivers. Please also update hpe-auxiliary RPM to v.1.0.3 for sles15sp3
  • This product correct an issue which the RPM metadata missing pci-id
    • ]]>
  • Improves data integrity
  • Decreases possibility of data corruption in certain error and timing conditions
  • Reduces the probability of hangs and provide a minor performance improvement
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for VMware 8.0
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Fixes an intermittent issue where the incorrect model number can be reported during spin-up.
    • ]]>         TBD

    ]]>
  • This product fix an issue that caused the driver to crash if it the vPort ID greater than the maximum supported vPorts.
  • This product fix an issue which the command returned an error although the link was up in ""mlx5cmd -linkspeed"". This happened when link up time exceeded 5 seconds.
    • ]]>         TBD

    ]]>
  • This product enhances the way ENS RSS support (receive side scaling) is added, enhancing performance.
  • This product enhances the way LRO (Large Receive Offload) support is enabled and disabled, improving network efficiency.
  • This product adds to support HPE MicroServer Gen11.
    • ]]>
  • This product fixes an issue where BFD controls were getting dropped (Bidirectional Forwarding Detection (BFD) protocol), ensuring network reliability.
  • This product fixes a problem where the ENS stack was invoking driver APIs with spinlock, improving system stability.
    • ]]>
  • This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.
  • The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.
  • Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         This Firmware package contains following firmware versions:

    Adapter

    Speed

    MBI

    Firmware

    UEFI

    Boot Bios
    HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter 32Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter 32Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter 64Gb 02.08.05 09.12.01 7.34 0.0
    HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter 64Gb 02.08.05 09.12.01 7.34 0.0

    Non-disruptive firmware upgrades: non-disruptive firmware updates is enabled and will not require a server reboot to apply.

    ]]>         Fixed the following behavior:

    Temperature Misreading: the adapter was reading incorrect reading of the temperature on the HPE SN1610Q 32Gb Fibre Channel Host Bus adapter's Small Form-factor Pluggable. The symptom would result in a temperature spike and potentially reset the system

     

    ]]>         This Firmware package contains following firmware versions:

    Adapter

    Speed

    MBI

    Firmware

    UEFI

    Boot Bios
    HPE SN1610Q 32Gb Dual Port Fibre Channel Host Bus Adapter 32Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1610Q 32Gb Single Port Fibre Channel Host Bus Adapter 32Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1700Q 64Gb Dual Port Fibre Channel Host Bus Adapter 64Gb 02.07.06 09.09.20 7.28 0.0
    HPE SN1700Q 64Gb Single Port Fibre Channel Host Bus Adapter 64Gb 02.07.06 09.09.20 7.28 0.0
    ]]>         The Firmware fixes the following:

    • Unsuccessful read of the SFP Temperature which will trigger a Server Shutdown. 
    • Message related to a Mailbox 0x48 Firmware dump saved to buffer.
    ]]>
  • This product now add message when set VF's MAC Address
  • This product now supports RHEL 9.1
    • ]]>
  • This product enhanced the wating time to wait MTU change.
  • This product enhanced ability to turn off CRC stripping for VF
    • ]]>
  • This product fixes an issue where it has race condition between iavf_open and iavf_handle_hw_reset
  • This product fixes an crash issue in iavf_suspend
  • This product fixes VF stuck in reset.
    • ]]>
  • Optimize sensor reporting to improve failure rate - AFR metrics
    • ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Reverted HDDQ spec 10.5.3 features to maintain compliance to OCP spec commands over NVMe-MI
  • Implemented real Active Measured Latency by adding OCP 2.0 C3 Log page
    • ]]>
  • OCP v2.0 feature support 
  • NVMe-MI over PCIe VDM support 
  • Bug fixes
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>         For Gen11 PR4 and  2023 Sep MSB

    ]]>         Support ML110 and DL560 Gen11 servers

    ]]>         TBD

    ]]>
  • This product enhanced optimize drvier around user data copy. 
  • This product enhanced driver warning messages are thrown when driver reload.
  • This product enhanced to support XDP multibuffer.
  • This product enhanced ethtool to support CMIS 4.0 and backwards compatibility apart from compat changes.
  • This product enhanced the compatibility with SLES15-SP4.
    • ]]>
  • This product addresses an issue where System crash on running ethtool self test in loop on multiple adapter ports
  • This product addresses an issue where MSIX collision between L2 and RoCE drivers.
  • This product addresses an issue where Devlink reload command failed.
  • This product correct an issue which unable to recover from FW crash triggered by bnxtnvm fwcli 'crash fw_assert'.
  • This product correct an issue which the call traces while unloading bnxt_en and bnxt_re driver
  • This product correct an issue which ethtool -S crash when firmware is unhealthy
  • This product correct an issue which rdev allocation '__flush_work' issue by doing initialization for kernel workqueue.
  • This product correct an issue which the RPM metadata missing pci-id
    • ]]>         This product adds to support HPE MicroServer Gen11

    ]]>         This product enhanced the compatibility with new kernel supported.

    ]]>         This product correct an issue which the RPM metadata missing pci-id

    ]]>
  • FW update to eliminate the risk of Drive missing issue.
  • Fixed low sequential write performance in Windows 2022
    • ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Problems Fixed:

    Addressed an issue where the MegaRAID controller status is displayed as "unknown" on the iLO web page.

    Known Issues:

    None]]>         Set the value of the Snoop Response Hold Off for IOAT Stack setting to 7 when the vRAN Workload Profile has been selected. This aligns with Intels performance tuning recommendation.

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Problems Fixed:

    Address an issue with some 4th Generation Intel Xeon Processors that can result in an unexpected reset with a machine check error logged to the Integrated Management Log (IML).  This issue is not unique to HPE systems.  The following is Intel’s description of the issue:  "Under complex microarchitectural conditions, the processor may experience a Caching Home Agent Table of Requests (TOR) timeout machine check exception."  This version of the System ROM will update internal processor firmware during boot.  This internal processor firmware cannot be downgraded even if the System ROM is downgraded. Using processors with different version of internal firmware is not supported.

    Addressed an issue where the speed of Kioxia EDSFF drive might be downgraded from PCIe Generation 5 to Generation 4.

    Known Issues:

    None

    ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Fixes a false indication of rare capacitor test failure
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Improve the FW about data mismatch after SPL issued.
    • ]]>
  • Improve the FW about data mismatch after SPL issued.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Supports VMware ESXi 7.0 U2 and ESXi 7.0 U3
    • ]]>
  • Supports VMware ESXi 7.0 U2 and ESXi 7.0 U3
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Improved AMS memory usage and performance.
    • ]]>
  • Fixed computer name only show upper case.
  • Fixed removed NVMe drives still show in cpqSePCIeDisk.
  • Fixed sending unsupported identify command to ODD.
  • Fixed AMS crash during session communication error with iLO.
  • Fixed IML missing when network status changed from disabled to enabled.
    • ]]>
  • Supported PCI multi-segment.
  • Enhanced NIC physical adapter configured speed and duplex up to 100g.
    • ]]>
  • Fixed missing enterprise OID in SNMP trap.
  • Fixed AHCI SATA drive firmware version won't synchronize after upgrading or downgrading firmware.
    • ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

    New features and changes included in version 20.38.1002:

    • Improved token calculation.
    • Added support for forwarding INT packets to the user application for monitoring purposes by matching the BTH acknowledge request bit (bth_a).
    ]]>         The following issues have been fixed in version 20.38.1002:

    • A link failure that occurred due to a wrong 'is_inphi_cable' indication.
    • Fixed a firmware assert that occurred when tried to verify if  the module supported  "swap".
    ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device's firmware to this release to improve the firmware security and reliability of your device.

     

    New features and changes included in version 20.37.1700:

    • A new capability enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Updated the link maintenance flow to avoid high uncorrectable error rate. 
    ]]>         No fixes in this version.

    ]]>
  • Fixes an issue in previous version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on
    • ]]>
  • Fixes an issue in previous version where the Inquiry model number is reported incorrectly for first few seconds after the drive is powered on
    • ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>         TBD

    ]]>
  • This product enhanced to add bnxt_re module parameter to specify the number of MSIX vectors per PF.
  • This product enhanced to add the support for rdma-core version v38, v39, v40, v41 and v24 in RoCE library.
    • ]]>
  • This product addresses an issue where System crash due to the race conditions between different bnxt_re driver operations
  • This product correct an issue which the bnxt_re driver crash or longer time to complete during unload under heavy RoCE I/O load.
  • This product correct an issue which the bnxt_re ifup initialization failed after aborted error recovery.
  • This product correct an issue which the Kernel panic when driver detect roce firmware command timeout.
  • This product correct an issue which the debugging bnxt_re printing to reduce the latency whenever the roce channel command timeout is detected.
  • This product correct an issue which ethtool -m could not dump the information for the SFF 0x1e module ID.
  • This product correct an issue which RoCE bandwidth very lower when load driver with no link present and speed forced to 10G.
  • This product correct an issue which system crash when enabling VF and vswitch bridging in a repeated cycle.
    • ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>         See the iSUT Release Notes for information about the issues resolved in this release

    ]]>
  • Fix for V6 Read disturb issue (which might have caused data integrity issue) and other issues.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • This firmware revision improves data integrity and reliability by optimizing adjacent track refresh parameters and management of emergency power loss table structure.
  • The risk of not upgrading to this firmware is the increased possibility of data corruption in emergency power loss events.
  • Several maintenance items are included in this firmware revision that reduce the probability of hangs and provide some minor performance improvements.
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Added support for Vmware 8.0
    • ]]>
  • Added support for Vmware 8.0
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         New release.

    ]]>         New release.

    ]]>
  • Updated supported platforms
    • ]]>
  • Added SHA384 signature
    • ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device firmware to this release to improve the firmware security and reliability of your device.
     
    New features and changes included in version 28.38.1002:

    • Added a new field/slot ID to PRS  pcie_cfg_data.pci_cfg_space.pciex.pcie_switch_ini_defined_base_slot_id = 3 to define a specific slot number for GPU bridge DSP.
    • Improved token calculation.
    • Added support for NC-SI channel on both ports.
    • Changed the protection mechanism for BAR configuration.
    • Updated the SX root to work with driverless mode in vport0 gvmi teardown.
    • Added support to the metadata reg_c 8-11 (packet fields) for matching and modifying the header, and Advanced Steering Operation (ASO) actions.
    • Added support for forwarding INT packets to the user application for monitoring purposes by matching the BTH acknowledge request bit (bth_a).
    • Implemented NVIDIA NC-SI OEM Commands:

        Get Electrical Sensor Count (command 0x13, parameter 0x6)
        Gel Electrical Sensor (command 0x13, parameter 0x7)
        Get Electrical Sensors (command 0x13, parameter 0x8)

    • Improved the IPsec CPS by using bulk allocation.

        For cases in which log_obj_range == 0, single IPSEC object will be allocated and initialized as before keeping backward compatibility.
        For better performance, it is recommended to work with IPsec bulk allocation and to initialize IPsec ASO context not via the firmware but via the hardware using ASO WQE.

    • Added support for a new value for coredump_type field in DPA_PROCESS_COREDUMP, [FIRST_ERROR_THREAD_DUMP (1).].
    ]]>         The following issues have been fixed in version 28.38.1002:

    • Fixed SPDM measurements signature.
    • An issue that prevented the system from detecting the PCIe device during slot DC power cycle tests.
    • Upgrading from firmware v28.36.1010 and below to v28.38.1002 no longer requires an upgrade to an intermediate version.
    • Updated the plug in/out events' reporting method to report only when the last recorded event is the opposite of the current event.
    • Fixed the SPDM operations order according to the spec. v1.1.0.
    • An issue that caused a packet with invalid/bad padcount to be silently dropped instead of sending a bad nack error.
    • Wrong credits configuration that occurred when MAX_ACC_OUT_READ was configured.
    • A rare deadlock case between 2 DC packets in the RX side.
    • A QoS host port rate limit shaper inaccuracy that occurred when the shaper was configured via the QSHR access register.
    • When using ConnectX-7 adapter card as InfiniBand, the port must be configured to use the Auto-Negotiation mode.
    ]]>         Security Hardening Enhancements: This release contains important reliability improvements and security hardening enhancements. HPE recommends upgrading your device firmware to this release to improve the firmware security and reliability of your device.
     
    New features and changes included in version 28.37.1700:

    • Removed the option to clear "Tx disable cap" for all non-baseT SFP modules.
    • Added a split mask verification process to check whether or not a module is split in HCA. 
    • Updated the NEGOTIATE_ALGORITHMS response according to the SPDM specification.
    • Added the option to clear the DPC registers after warm reboot.
    • Changed the initial Tx preset configuration for the DownStream port (DSP).
    • Added mergeable buffer support (VIRTIO_NET_F_MRG_RXBUF in virtio spec) for VDPA kernel mode to improve performance in case of large MTU such as 9K. The feature is disabled by default and must be manually enabled while creating or modifying the virtio device.

    Note: For best performance, it is NOT recommended to enable the feature if the VDPA MTU is set to the default value (1500).

    • A new capability that enables the VM to track and limit its Vport's activity. This is done using the new q_counters counter which enables aggregation of other Vport's from PF GVMI.
    • Added a flow rule that enables offloading of multicast traffic by broadcasting it to multi-Flow-Table in FDB.
    • Selective repeat improves network utilization in case of a lossy fabric. This features is enabled by default.
    • Added support for dynamic MSIX modification on a VF NVME device emulation.

    If a PF NVME device emulation is created with dynamic_vf_msix_control = 1, then the dynamic_vf_msix_reset can set the PF device emulation's VF MSIX number to 0. The num_msix is used in the modified VF device emulation to modify the MSIX number of the VF device emulation.

    • Enabled IB CC per Service Level (SL) for RC/UC on the HCA side.

    Now different SLs can be configured to be CC on/off according to the bitmask decided by the software.

    • Optimizes the ATC configuration dynamically based on the returned pages of the ATS translation requests that have been made.
    • Enables a smooth and statically switch between PCC algorithms. In addition, the user can now switch between PCC algorithms while running traffic.
    • Added support for 32 actions in the header modify pattern using bulk allocation.
    • The software can explicitly set the SL of an RTT response packet, instead of it being taken from the RTT request packet's SL. The RTT response packet SL may be set/queried via the CONGESTION_CONTROL_HCA_NP_PARAMETER MAD.
    ]]>         The following issues have been fixed in version 28.37.1700:

    • Firmware crashed when setting large payload length values (more than ~1500) in NC-SI command's header.
    • Interface type was shown as "unsupported" in CMIS modules.
    • Fixed the configuration of the TS1s sent by the DownStream port (DSP) when moving to EQLZ.ph2.
    • PLDM firmware update process failed in case 1304 bytes chunk size is chosen.
    • An issue that occurred during secure firmware update when decrypting and authenticating each chunk of data using its authentication tag. The issue appeared when the main code chunk was split between the user chunks and any GCM operation (e.g., flash read with decryption). This GCM operation broke the GCM context for main chunk authentication and therefore failed. 
    • CNP received, handled, and ignored counters in the hardware counters could not work after moving to Programmable Congestion Control mode.
    • Hardware failed to handle an error flow that occurred when accessing the DPA cluster L2 cache from the firmware processor. In this case the firmware processor hardware requested a VA=>PA translation from the internal mmio, and the address translation was broken by the mmio on the 4K page boundary.
    • Hardware failed to consume Port-VL and credits, which consequently blocked traffic from being transmitted due to a race condition between the firmware and the hardware when accessing the chip memory (CR space).
    ]]>
  • Reduced the occurrence probability of PMIC busy issue by stopping PLP capacity check to reduce i2c access to PMIC.
    • ]]>
  • Added support for RHEL 9.
    • ]]>         Updated to driver version 14.2.589.10-1

    ]]>         Updated to driver version 14.0.499.31

    ]]>         Updated to version 9.4.8.20

    ]]>         Updated to version 9.4.6.20

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>
  • Fixed incorrect slot type is displayed on Gen11 SR416ie-m and SR932i-p storage controllers.
    • ]]>         Agentless Management Service

    • Extend network adapter speed support with 20,40, and 100G for CPQNIC MIB cpqNicIfPhysAdapterConfSpeedDuplex OID.
    ]]>         Agentless Management Service

    • Fixed incorrect NVMe drive information displayed after hot plugging.
    • Fixed SSD wear status sudden peak value triggering SNMP trap false alarm.
    ]]>
  • Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.
    • ]]>
  • This product enhanced NDIS packet drop monitoring support for Windows Server vNext.
  • This product enhanced to Implement RoCE variable size WQE(Work Queue Element) support for RDMA.
    • ]]>
  • This product addressed the code initialization in NDSPI(Network Direct Service Provider Interface) to enhance retransmit capability.
  • This product addressed the data retrieval for better RDMA connection.
  • This product addressed the disablement support of CQ overflow detection.
    • ]]>
  • This product enhances to support information logging of DBQ (Database Qualifier) events.
  • This product enhances to address a new method of retrieving data from the correct PFs by using the correct index value.
  • This product enhances to use I/O Workitem EX to handle passive level callbacks instead of standard NDIS workitems.
  • This product removes the Packet Direct advanced control panel options.
  • This product adds to support HPE MicroServer Gen11
    • ]]>         This product fixes an issue where the VF RoCE would not function if the default VLAN is enabled on vSwitch for the VF

    ]]>         Support new ML110 and DL560 Gen11 servers

    ]]>         Support new ML110 and DL560 Gen11 servers

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Problems Fixed:

    Address an issue that can result in a Red Screen of Death (RSOD) and hang during system boot or a hang during system boot without an RSOD. This issue can occur on systems utilizing the v1.32 or v1.40 System ROM revision and iLO Firmware revision v1.50. The v1.32 System ROM added a boot-time reduction capability (which also required iLO Firmware revision v1.50) which resulted in the boot-time RSOD and/or hang. This capability has been removed in this revision of the System ROM.

    Addressed an issue where one-time boot did not work properly after setting one-time boot device from iLO web or via Redfish.

    Known Issues:

    None]]>         Removed "NUMA memory domains per socket" selection item "Auto" from RBSU, because value of Auto option is actually set to one memory domain per socket. Set display default to "One memory domain per socket".

    Added "NVMe PCIe Resource Padding" option under "Advanced PCIe Configuration" in RBSU. The option is for fixing a failure to hot add NVMe drive to empty slot under OSes such as VMware. The option can be set from Redfish URI "/redfish/v1/systems/1/bios/settings/" with property "PciResourcePadding".

    ]]>         Important Notes:

    This revision of the System ROM includes AMD reference code GenoaPI 1.0.0.8 for AMD 4th Generation EPYC processors.

    Firmware Dependencies:

    None

    Problems Fixed:

    This revision of the System ROM includes the revision of the OpenSSL library 1.1.1u update which provides mitigation for and security vulnerabilities documented as CVE-2023-2650.

    Addressed an issue where the unsupported DIMM population IML will report an incorrect processor number on dual-processor systems.

    Addressed an issue where the SMBIOS type 197 might contain an incorrect format value of xGMI speed.

    Addressed an issue where the CXL root bridge was missing from SMBIOS type 9.

    Addressed an issue where dmidecode indicates 4 power supplies are installed when only 2 power supplies are actually installed.

    Addressed an issue where number of "Internal L3 cache" displayed under RBSU information page is not correct.

    Addressed an issue where the System Health LED is illuminated Red for all memory configuration error cases. Some memory configuration error cases are not critical and should have the System Health LED illuminated Amber.

    Known Issues:

    None]]>         This product now supports VMware vSphere 8.0.

    ]]>         TBD

    ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • Added support for Microsoft Windows Server 2022.
    • ]]>
  • VENDOR IDENTIFICATION field changed from “HP” to “HPE” and Reliability improvements.
    • ]]>         This product addresses an issue where Loses IP Address Randomly during AC/DC cycle and idling.

    ]]>         This product addresses an issue where the FAN behavior with installed BCM 5719 1Gb 4p BASE-T OCP Adptr.

    ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This is the initial version of the firmware.

    Known Issues:

    None

    ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>         Important Notes:

    None

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This is the initial verison of the firmware.

    Known Issues:

    None

    ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>
  • Added support for Microsoft Server Windows 2022.
    • ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for 4th Generation Intel® Xeon® Scalable Processors.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for 4th Generation Intel® Xeon® Scalable Processors.

    Known Issues:

    None

    ]]>         Important Notes:

    This version of the Server Platform Services (SPS) Firmware contains the latest package for Intel Sapphire Rapids.

    Firmware Dependencies:

    None

    Enhancements/New Features:

    This version contains the latest Server Platform Services firmware for Intel Sapphire Rapids.

    Known Issues:

    None

    ]]>
  • Improve the FW about data mismatch after SPL
    • ]]>
  • Added support for Microsoft Windows Sever 2022.
    • ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>
  • Fixes the Power Coordination algorithm which ensures the drive will properly negotiate power with SPL-2 and newer compliant controllers.
    • ]]>         For Gen11 PR4 and 2023 Sep MSB

    ]]>         Support ML110 and DL560 Gen11 servers

    ]]>
  • Fix bugs found in the previous version and improve on TTR (Time To Ready) requirement to fix device temporarily not found issue after hot-plug.
    • ]]>
  • Fix bugs found in the previous version and improve on TTR (Time To Ready) requirement to fix device temporarily not found issue after hot-plug.
    • ]]>
  • Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.
    • ]]>         The following changes and new features have been included in version 23.04-1.1.3.1

    • Starting this release, MLNX EN+RoCE drivers will adopt the following versioning naming scheme: YY.MM-x.x.x.x (i.e., Year.Month-x.x.x.x).
    • Added support for allowing the host to track various statistics for the VFs, specifically all of the Q_counters stats even if he gives the VF to a VM, through the representor Q_counters for the VF which are now exposed over the host.
    • With this feature, a kernel error log is now generated when certain fatal QP errors occur.
    • Added support for the following operating systems:
      • RHEL 9.2
      • RHEL 8.8
      • SLES15-SP5
    ]]>         The following issues have been fixed in version 23.04-1.1.3.1:

    • Installing "mlnx_tune" on Python3 did not work properly. "mlnx_tune" now supports Python3 in addition to Python2.
    • Changing traffic class via the sysfs while modifying QPs in parallel caused a deadlock.
    • Due to a bug in the emulation layer, performance degradation was experienced when running GPUDirect over Virtual Functions.
    • "debugfs" directories could not be created for representors and sub-functions, thus the log showed error for both the scenarios.
    • "knem" did not fully support RHEL8.7 and newer releases.
    ]]>         This product correct an issue which the component can't read the current driver version.

    ]]>         This product now supports HPE ProLiant Gen11 Platforms with Intel processors

    ]]>
  • Firmware addresses a hot plug reporting concern
    • ]]>
  • Firmware addresses a hot plug reporting concern
    • ]]>         This product now supports  ResetToDefault property(RDE Port Schema).

    ]]>         This product addresses an issue where InterfaceEnabled property is read only and it can't patch this property

    ]]>
  • This product now supports RDE Read and Write operations.
  • This product now supports Debug Dump feature.
  • This product now supports new parameters when software requesting on Port 0(via AQ the connectivity type)
    • ]]>         New version with v1.10.

    ]]>
  • Initial version with PLDM header
    • ]]>
  • Added support for Remote Key Management of Managed SED.
  • Added the Authority Key Identification 'security show' command in the SSA CLI for SPDM.
    • ]]>
  • Fixed an issue in SSA CLI where failed drive details were shown twice in the show config output.
  • Fixed an issue in SSA CLI where an error message was not being generated while performing an invalid modify command.
  • Fixed an issue in SSA CLI where the tool would display a Reboot required reason when modifying MRRS value to same value.
  • Fixed an issue in SSA CLI that would display an invalid error string in the show foreignmasterkeyidentifier output with Managed SEDs.
  • Updated SSA CLI to not list drivetypes that do not have the correct number of drives to modify an array with Managed SEDs.
  • Fixed an issue in SSA Scripting where a volume creation would fail when Remote SED mode was enabled and waiting for reboot.
    • ]]>         Initial Release

    ]]>
  • Added support for Qualcomm X100
  • Added enhanced support to iLO firmware to report additional description about the components for HPE GreenLake Compute Ops Management initiated firmware bundle update
  • Added support to enable or disable User Accounts through Redfish and iLO web interface
  • In-band IPMI support for HPE ProLiant RL300 Gen11 servers (RHEL 8.6)
  • For PLDM components, added support to selectively update the target devices on the system through Install Sets and Task Queue
    • ]]>
  • Fixed CloudConnect retry logic to reconnect to iLO once connectivity is resumed
  • Fixed the auto-connect issue if the HPE GreenLake Compute Ops Management (COM) was disabled due to a no-retry
    • ]]>
  • iLO needs to provide IPv4 address for RDE enabled NIC
  • NVIDIA L40S needs to be enabled on HPE Servers (Gen11, Gen10 Plus)
  • iLO enablement for Intel Ponte Vecchio (PVC) for accelerator manageability and supportability
  • Reduce EDSFF power consumption using NVMe Power States feature
  • iLO enhancements to support SMBIOS 3.86 spec (type 197 and 242)
    • ]]>
  • Increased the maximum boot order to 512 as specified by UEFI EV specification
  • Incorrect sensor values for some sub-components in IPMI response
  • The "Ignore" option for the "Global Component Integrity" security parameter in the iLO Security Dashboard gets automatically disabled
  • The discrepancy between M.2 Slot Name with Redfish URI and iLO GUI is removed. The product name getting from backend will be displayed in redfish and UI as well
  • Enforced a limit of 14 bytes for DHCP v4 clientId. An error response of "400 - Bad Request" will be observed if the length is beyond 14 characters
  • Removal of duplicate sensor entries from IPMI response
  • UefiDevicePath length increased from 256 bytes to 1024 bytes
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Added support for RHEL 9.
    • ]]>
  • Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.
    • ]]>
  • Fix contains optimization to increase the time for Recovery operation and few checks for maintenance.
    • ]]>         This product addresses an issue where Loses IP Address Randomly during AC/DC cycle and idling.

    ]]>         This product addresses an issue where the FAN behavior with installed BCM 5719 1Gb 4p BASE-T OCP Adptr.

    ]]>