To get the list of all dependency files for hp-health, type:
rpm –qp –requires hp-health-< version >.rpm
]]>To install the package type:
rpm -ivh hp-health-<version>.rpm
To check whether the package is loaded properly type:
/etc/init.d/hp-health status
Additional help is available by typing:
man hp-health
or
man hp_mgmt_install
]]>
]]>
http://www.hpe.com/storage/spock/
The HPE supplied fibre channel driver must be installed prior to this enablement kit component if you want to enable Smart SAN functionality. The driver is available on the HPE.com website at www.hpe.com.
Red Hat Enterprise Linux 6 Server (x86-64) FCoE/FC Driver Kit for HPE Qlogic CNAs, HBAs and mezzanine HBAs, version 8.07.00.42.06.0-k1
Red Hat Enterprise Linux 7 Server FCoE/FC Driver Kit for HPE QLogic CNAs, HBAs and mezzanine HBAs and CNAs, version 8.07.00.42.07.0-k1
SUSE Linux Enterprise Server 11 (AMD64/EM64T) FCoE/FC Driver Kit for HPE Qlogic CNAs, HBAs and mezzanine HBAs, version 8.07.00.42.11.3-k
SUSE Linux Enterprise Server 12 FCoE/FC Driver Kit for HPE QLogic CNAs, HBAs and mezzanine HBAs and CNAs version 8.07.00.42.12.0-k1
However, if a Smart SAN enabled driver is not installed at execution time, the component will land the enablement kit files for future use after the driver has been installed.
]]>
# rpm -e hpe-qlogic-smartsan-enablement-<version>.noarch.rpm
This is a configurable component. It requires a configuration file in order to enable/disable Smart SAN functionality. If no configuration is performed, the current Smart SAN status is stated and the execution is complete. No further action is taken.
For detailed information about configurable components, see the Smart Update Manager User Guide at http://www.hpe.com/support/HP_SUM_UG_en.
Component execution outside of HPE Service Pack for Proliant:
1. Login as the system administrator (root).
2. Download the RPM to a directory on your hard drive and change to that directory.
3. To install, type the following command at the prompt:
# rpm -ivh hpe-qlogic-smartsan-enablement-kit-<version>.x86_64.rpm
Example: # rpm -ivh hpe-qlogic-smartsan-enablement-kit-3.3-3.x86_64.rpm
4. When the installation or upgrade is complete, the following message displays:
Installation complete
# rpm -e hp-fc-enablement-<version>.noarch.rpm
To install the vendor specific enablement RPM use the following command:
# rpm -ivh HP-CNA_FC-hpqlgc-enablement-<version>.noarch.rpm
This version of the enablement kit does not provide the additional functionality of rebuilding the ram disk or setting driver parameters as the previous versions had done. Please refer to the “Additional setup” section of the Native Linux Device-Mapper Multipath for HPE StorageWorks Arrays reference guide for instructions on how to perform these functions. The reference guide is available at the following link:
http://www.hpe.com/storage/spock/
]]>
To install the package type:
rpm -ivh hp-ams-<version>.rpm
To check whether the package is loaded properly type:
/etc/init.d/hp-ams status
Additional help is available by typing:
man hp-ams
]]>Verify that the HP iLO 4 is talking to SNMP from a Linux system with net-snmp utilities installed:
snmpwalk -t 60 -v 2c -Ox -c iLO4_configured_community_string iLO4_IP_Address 1.3.6.1.4.1.232.1.1
Verify that HP AMS is operating on the Server:
snmpwalk -t 60 -v 2c -Ox -c iLO4_configured_community_string iLO4_IP_Address 1.3.6.1.4.1.232.5.1
]]>To install or upgrade the driver type:
Setup is now complete. Please REBOOT your computer NOW!!
NOTE: If the installation fails or if you see any warning or error messages, STOP, do NOT reboot the computer. The driver will not be operational and you must uninstall the driver by typing the following command:
Enterprise Support
For support on Smart Array controllers, visit http://www.hpe.com/support
]]>
amsd only supported on HPE Gen10 Servers.
amsd provides information to the iLO 5 service providing SNMP support.
SNMP PASS-THRU on the iLO 5 MUST be disabled, and SNMP should be configured on the iLO 5. The iLO 5 may need to be reset after changing these settings.
Requirements:
Minimum iLO 5 Firmware Version = 1.1
Minimum supported OS Versions = SuSE Linux Enterprise Server 12 SP2
To get the list of all dependency files for hp-smh-templates type:
rpm –qp –-requires hp-smh-templates-<version>.rpm
]]>To install the package type:
rpm -ivh hp-smh-templates-<version>.rpm
To check whether the package is installed type:
rpm –q hp-smh-templates
Additional help is available by typing:
man hp-smh-templates
]]>The management interface driver and management agents must be installed on the server.
For iLO 5, openssl v1.0.x or later is required in addition to above packages.
Customers who manually compile and install openssl or intentionally relocate /usr/bin/openssl, need to set PATH environment variable to direct HPONCFG to the right/intended openssl.
If a previous version of the Hponcfg utility has been installed, it must be removed before this package can be installed. To remove the previous version of the package, type the following :
To install the package, type:
After installation, the executable for hponcfg utility can be found under the directory /sbin.
]]>IMPORTANT UPDATE: HPE SSA (GUI) for Linux can now be run without requiring the HPE System Management Homepage. HPE SSA now supports a Local Application Mode for Linux. The HPE System Management Homepage is still supported, but no longer required to run the HPE SSA GUI.
To invoke, enter the following at the command prompt:
ssa -local
The command will start HP SSA in a new Firefox browser window. When the browser window is closed, HP SSA will automatically stop. This is only valid for the loopback interface, and not visible to external network connections.
For support for HPE SSA or Smart Array controllers, please visit Contact HP.
]]>To install or upgrade the driver type:
# rpm -Uvh hpdsa-kmp-<version>.<OSupdate>.x86_64.rpm
Setup is now complete. Please REBOOT your computer NOW!!
NOTE: If the installation fails or if you see any warning or error messages, STOP, do NOT reboot the computer. The driver will not be operational and you must uninstall the driver by typing the following command:
# rpm -e hpdsa-kmp-<version>.<OSupdate>.x86_64.rpm
Enterprise Support
For support on Smart Array controllers, visit http://www.hpe.com/support
MAKING DRIVER UPDATE USB-KEY UNDER A LINUX-LIKE OS:
# dd if=hpdsa-<version>.sles12.x86_64.dd of=/dev/sdz
INSTALLATION
At the initial OS installation screen be sure to:
blacklist=ahci dd
Enterprise Support
For support on Smart Array controllers, visit http://www.hpe.com/support
http://www.hpe.com/storage/spock/
The HPE supplied fibre channel driver must be installed prior to this enablement kit component if you want to enable Smart SAN functionality. The driver is available on the HPE.com website at www.hpe.com.
Linux FC Driver Kit for HPE Branded Emulex FC HBAs and mezz cards, version 11.1.183.21, for RedHat 6, RedHat 7, and Novell SUSE 11, SUSE 12
However, if a Smart SAN enabled driver is not installed at execution time, the component will land the enablement kit files for future use after the driver has been installed.
]]>
# rpm -e hpe-emulex-smartsan-enablement-<version>.noarch.rpm
This is a configurable component. It requires a configuration file in order to enable/disable Smart SAN functionality. If no configuration is performed, the current Smart SAN status is stated and the execution is complete. No further action is taken.
For detailed information about configurable components, see the HP Smart Update Manager User Guide at http://www.hpe.com/support/HP_SUM_UG_en.
Component execution outside of HPE Service Pack for Proliant:
1. Login as the system administrator (root).
2. Download the RPM to a directory on your hard drive and change to that directory.
3. To install, type the following command at the prompt:
# rpm -ivh hpe-emulex-smartsan-enablement-kit-<version>.x86_64.rpm
Example: # rpm -ivh hpe-emulex-smartsan-enablement-kit-1.0.0.0-1.x86_64.rpm
4. When the installation or upgrade is complete, the following message displays:
Installation complete
]]>
To install or upgrade the driver type:
Setup is now complete. Please REBOOT your computer NOW!!
NOTE: If the installation fails or if you see any warning or error messages, STOP, do NOT reboot the computer. The driver will not be operational and you must uninstall the driver by typing the following command:
Enterprise Support
For support on Smart Array controllers, visit http://www.hpe.com/support
]]>
To get the list of all dependency files for hp-snmp-agents type:
rpm –qp –-requires hp-snmp-agents-<version>.rpm
]]>To install the package, type:
rpm -ivh hp-snmp-agents-<version>.rpm
To check whether the package is loaded properly type:
/etc/init.d/hp-snmp-agents status
Additional help is available by typing:
man hp-snmp-agents
]]>